Reviews Fittings Valves

SharkBite U256LFCP 3/4 Inch 90 Degree Elbow Push to Connect Pipe Fitting, 10 count, Brass

  • INSTALLS IN SECONDS: Repair with no special tools, soldering, crimping, or glue.
  • Just push to create a quick watertight union with SharkBite pushfit connectors.
  • VERSATILE: SharkBite plumbing fittings fit copper, CPVC, and PEX pipe and connect all 3 types in any combination.
  • LEAD-FREE: Made of high-quality forged DZR brass that is lead-free. Ball valves, shutoffs, and compression fittings, are safe for potable water lines.
  • PREFERRED BY THE PROS: All SharkBite fittings meet the same standards for commercial and residential plumbing applications.
  • MADE IN THE USA: All SharkBite valves, joints, and adapters are manufactured and tested in the USA.
Check Stock

Wostore Flaring Swage Tool Kit for Copper Plastic Aluminum Pipe With Tubing Cutter & Ratchet Wrench

  • 【ALL IN ONE KIT】：The kit includes 1 flaring cone, 2 flaring bars, 5 swage fittings, 1 tubing cutter, 1 ratchet wrench and 1 storage case..
  • 【EXTENSIVE RANGE OF FLARE ADAPTERS】：Flaring tool apply to 1/8", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 5/8", 3/4" O.D. tubing..
  • 【COMMON SWAGE FITTINGS】:Swage fittings are used to 3/16”, 1/4”, 5/16”, 3/8”, 1/2”, 5/8”,3/4" O.D. tubing, a rugged and durable flaring....
  • 【PRACTICAL TOOLS】:Tube cutter:1/8"-1-1/8" (3-28MM) Pipe, Ratchet wrench:3/16",1/4",5/16",3/8" for square valves, such as valves on hose bibs and....
  • 【DURABILITY AND ACCURACY】:This flaring kit swivel-type swaging adapters and flaring cone are made of the sturdiest steel and chromed for easy....
Check Stock

Habitech 2-Pack In-Line Barbed Ball Valve 13mm For 1/2 Inch Tubing .520 ID - Regulate and Shut-Off/On Water Flow

  • ...l, use as tank valves, drain valves, return valves or in any situation where fluid restriction is needed. For use with irrigation, aquarium plumbing, pump return line, saltwater applications, RV camper and trailers, pex tubing, hydroponics, and aquaponics..
  • Leak-Free Seal: These non-corrosive plastic flow valve fittings are guaranteed to provided a secure, watertight connection that handles an operating pressure of up to 45 PSI. Constructed to be wear-resistant to assure long term reliability of connections. Confidently install these barbed fittings without clamps by using our Valve Sizing Chart (see photo) to get the perfect fit. Match the ID (Inner Diameter) of your hose or tube with the acceptable IDs listed on the chart..
Check Stock

Firestone W217602445 Ride-Rite Kit for Toyota Tundra

  • Levels vehicle front-to-rear and side-to-side , Fits 2007 to 2013 models.
  • Stabilizes vehicle while loaded and maximizes vehicles load carrying capacity.
  • Used on pick-ups, class A,B,C motorhomes, vans, commercial vehicles and SUV's.
  • Kit includes air springs, air line, fasteners, upper and lower brackets, inflation valves, push-to-connect air fittings and detailed instructions.
  • Levels vehicle front-to-rear and side-to-side , Fits 2007 to 2013 models..
  • Adjustability is between 5-100 Pascal per square inch.
Check Stock

Morvat Heavy Duty Brass 2 way Y Splitter Garden Hose Hexagonal Connector with Comfortable Grip Shut Off Valves, Adapter for Water Tap, Outlet, & Spigot, Includes 2 Extra Rubber Washers & Teflon Tape

  • DOUBLE YOUR WATER SOURCE: Instantly create two tap outlets with this ultra-durable hose splitter. The dual-valve design features built-in shut-off valves with updated and easier to grip handles! The adjustable flow control valves make it easy to use this hose splitter as a garden hose pressure regulator..
  • UNIVERSAL COMPATIBILITY: Fitted with US Standard NH 3/4" threads for use with most water source fittings..
  • RUGGED HEAVY-DUTY 100 % LEAKPROOF DESIGN: Constructed of the highest quality brass for superior durability and longevity. Easily withstands high water pressure in all outdoor weather conditions without breaking, rusting, or corroding. Utilizes expertly machined fittings and high-quality ball valves to provide a watertight seal preventing any leaks or drips..
  • HEAVY DUTY TOP CONNECTION: Easily screw the 2-way splitter by hand or wrench with the updated hexagonal top connection. The 360° rotatable swivel connection securely attaches to any water source..
Check Stock

PIPE DÉCOR 0000 LDR Industrial Steel Grey 1-1/4 x ½ -Inch Reducing Coupling Pipe Fittings (4-Pack), Dark Metal

  • Get Creative and Add Style To Any Home, Office Or Interior Space with LDR Pipe Decor fittings and connectors. From standard to unique and innovative fittings, the types of furnishings you can create are limitless.
  • Two pieces, 1-1/4 x ½ -Inch Reducing Coupling Pipe Fittings for compatibility with other project materials such as lamp parts, valves, etc..
  • LDR Pipe Décor Fittings and Attachments Are Made From The Highest Quality Materials. Great for all your Do It Yourself Industrial pipe projects. Can be painted any color to match your project!.
  • Standard Industrial Grey Finish, constructed from sturdy malleable iron Threads and materials, and meet ASME and ASTM standards.
  • This Item Is an Authentic Malleable Iron Fittings which gives a beautiful rustic look and requires necessary cleaning and sealing prior to use.
Check Stock

Watts Tankless Water Heater Service Valve Kit

  • TANKLESS WATER HEATER VALVE KIT: Watts LFTWH-FT-HCN service valve kit for tankless water heater valves simplify the installation, maintenance and operation of tankless water heaters..
  • SERVICE VALVE KIT FOR TANKLESS WATER HEATER: The tankless water heater service valve kit replaces up to 18 fittings and 16 connections used in typical tankless water heater installations, color-coded tee handle. Optional pressure relief and check valve..
  • MULTIPLE CONNECTION VALVE KIT: They are available in two valve sets or as a single valve with female threaded, union or quick-connect end options. The service valve kits are available with or without a relief valve. Facilitate service and maintenance with cold water inlet and hot water outlet valves certified to NSF/ANSI 61..
  • LEAD FREE VALVE KIT: The wetted surface of our Lead Free products contacted by consumable water contain less than one quarter of one percent (0.25 percent) of lead by weight..
  • WATER SERVICE VALVE KIT: Purge/drain ports allow regular cleaning to remove scale build-up. The kit includes LF4L - Lead free poppet type pressure relief valves for protection against excessive pressure and LFTWH - Lead Free Tankless Water Heater Valves..
Check Stock

Unisex Adult Steampunk Gas Mask Costume Accessory, Gold, One Size

  • TANKLESS WATER HEATER VALVE KIT: Watts LFTWH-FT-HCN service valve kit for tankless water heater valves simplify the installation, maintenance and operation of tankless water heaters..
  • SERVICE VALVE KIT FOR TANKLESS WATER HEATER: The tankless water heater service valve kit replaces up to 18 fittings and 16 connections used in typical tankless water heater installations, color-coded tee handle. Optional pressure relief and check valve..
  • MULTIPLE CONNECTION VALVE KIT: They are available in two valve sets or as a single valve with female threaded, union or quick-connect end options. The service valve kits are available with or without a relief valve. Facilitate service and maintenance with cold water inlet and hot water outlet valves certified to NSF/ANSI 61..
  • LEAD FREE VALVE KIT: The wetted surface of our Lead Free products contacted by consumable water contain less than one quarter of one percent (0.25 percent) of lead by weight..
  • WATER SERVICE VALVE KIT: Purge/drain ports allow regular cleaning to remove scale build-up. The kit includes LF4L - Lead free poppet type pressure relief valves for protection against excessive pressure and LFTWH - Lead Free Tankless Water Heater Valves..
Check Stock

SharkBite 1/2 Inch Disconnect Tongs for Push to Connect Brass Plumbing Fittings, U711

  • SHARKBITE REMOVAL TOOL: 1/2 inch disconnect tongs allow for brass push connect fittings to be disconnected from the pipe quickly and easily.
  • can remove or adjust push to connect fittings in tight spaces for easy disassembly.
  • COPPER, PEX, CPVC, CTS, HDPE: SharkBite disconnect tong is compatible with copper tubing, CTS, CPVC, HDPE, and PEX fittings, and connects all three types in any combination, ideal for working in tight work spaces.
  • DURABLE AND HIGH QUALITY: Fitting remover is made with durable stainless steel and wide grip handles by a name you know and trust.
  • SharkBite's quality and performance are field-proven and trusted in the plumbing industry.
  • PREFERRED BY THE PRO: SharkBite tools and fittings meet the same high standards for commercial and residential plumbing applications, combining durability and ease of use suitable for commercial repairs or home improvement projects.
  • MADE IN THE USA: All SharkBite valves, clips, joints, and adapters are manufactured and tested in the USA.
Check Stock

Class A Customs 40 Gallon RV Waste Black Water Holding Tank WT-4000

  • 40 Gallon RV Waste Water Holding Tank MADE IN THE USA by Class A Customs using Medium Density Polyethylene (MDPE) Resin TANK NOT FOR FRESH OR DRINKING WATER USE – WASTE/GRAY WATER USE ONLY – Used in RV’s Campers, Trailers, Motorhomes and Tiny Houses.
  • INSTALLED OUTLET 3” ABS Female Pipe - outlet can not be moved DO NOT over-tighten fittings damage will occur Dump valves do not hook directly to the 3" ABS fitting, from the outlet run PVC or ABS piping (not included), dump valve (not included) is added to the piping..
  • INLET & VENT INSTALLATION Class A Customs Black Water Tanks only come with the outlet the end user will determine where the inlet and vent will need to be placed and install, hardware NOT included. TANK MUST BE VENTED allowing air in and out when in use. *DO NOT PRESSURIZE TANK* DO NOT over-tighten fittings damage will occur..
  • NOT INCLUDED Inlet and Vent Fittings / Additional Fittings / Hardware / Mounting Hardware / Dump Valve / Piping NOT INCLUDED.
Check Stock

Class A Customs 27 Gallon RV Waste Black Water Holding Tank WT-2700

  • 27 Gallon RV Waste Water Holding Tank MADE IN THE USA by Class A Customs using Medium Density Polyethylene (MDPE) Resin TANK NOT FOR FRESH OR DRINKING WATER USE – WASTE/GRAY WATER USE ONLY – Used in RV’s Campers, Trailers, Motorhomes and Tiny Houses.
  • INSTALLED OUTLET 3” ABS Female Pipe - outlet can not be moved DO NOT over-tighten fittings damage will occur Dump valves do not hook directly to the 3" ABS fitting, from the outlet run PVC or ABS piping (not included), dump valve (not included) is added to the piping..
  • INLET & VENT INSTALLATION Class A Customs Black Water Tanks only come with the outlet the end user will determine where the inlet and vent will need to be placed and install, hardware NOT included. TANK MUST BE VENTED allowing air in and out when in use. *DO NOT PRESSURIZE TANK* DO NOT over-tighten fittings damage will occur..
  • NOT INCLUDED Inlet and Vent Fittings / Additional Fittings / Hardware / Mounting Hardware / Dump Valve / Piping NOT INCLUDED.
Check Stock

Class A Customs 14 Gallon RV Waste Black Water Holding Tank WT-1400

  • 14 Gallon RV Waste Water Holding Tank MADE IN THE USA by Class A Customs using Medium Density Polyethylene (MDPE) Resin TANK NOT FOR FRESH OR DRINKING WATER USE – WASTE/GRAY WATER USE ONLY – Used in RV’s Campers, Trailers, Motorhomes and Tiny Houses.
  • INSTALLED OUTLET 3” ABS Female Pipe - outlet can not be moved DO NOT over-tighten fittings damage will occur Dump valves do not hook directly to the 3" ABS fitting, from the outlet run PVC or ABS piping (not included), dump valve (not included) is added to the piping..
  • INLET & VENT INSTALLATION Class A Customs Black Water Tanks only come with the outlet the end user will determine where the inlet and vent will need to be placed and install, hardware NOT included. TANK MUST BE VENTED allowing air in and out when in use. *DO NOT PRESSURIZE TANK* DO NOT over-tighten fittings damage will occur..
  • NOT INCLUDED Inlet and Vent Fittings / Additional Fittings / Hardware / Mounting Hardware / Dump Valve / Piping NOT INCLUDED.
Check Stock

Class A Customs 31 Gallon RV Waste Black Water Holding Tank WT-3100

  • 31 Gallon RV Waste Water Holding Tank MADE IN THE USA by Class A Customs using Medium Density Polyethylene (MDPE) Resin TANK NOT FOR FRESH OR DRINKING WATER USE – WASTE/GRAY WATER USE ONLY – Used in RV’s Campers, Trailers, Motorhomes and Tiny Houses.
  • INSTALLED OUTLET 3” ABS Female Pipe - outlet can not be moved DO NOT over-tighten fittings damage will occur Dump valves do not hook directly to the 3" ABS fitting, from the outlet run PVC or ABS piping (not included), dump valve (not included) is added to the piping..
  • INLET & VENT INSTALLATION Class A Customs Black Water Tanks only come with the outlet the end user will determine where the inlet and vent will need to be placed and install, hardware NOT included. TANK MUST BE VENTED allowing air in and out when in use. *DO NOT PRESSURIZE TANK* DO NOT over-tighten fittings damage will occur..
  • NOT INCLUDED Inlet and Vent Fittings / Additional Fittings / Hardware / Mounting Hardware / Dump Valve / Piping NOT INCLUDED.
Check Stock