Reviews Encoder Module

Encoder Metal Gearmotor 12V DC High Speed 300RPM Gear Motor with Encoder for Arduino and 3D Printers

  • ★The rotary encoder can count the number of pulse output during rotation in the positive direction and reverse direction through the rotation and this rotation counts are not limited.
  • ★With the key on the rotary encoder, you can reset to the initial state, that is, counting from 0.
  • ★The Material of Knob Cap: aluminium alloy；The Specification of Knob Cap: diameter: 15mm/ 0.59in.
  • ★Package content: 10pcs x Rotary Encoder Module，10pcs black Knob ..
Check Stock

Maxmoral 2pcs Rotary Encoder Module KY-040 360 Degrees for Arduino Compatible Brick Sensor Switch Development Board

  • The Material of Knob Cap: aluminium alloy.
  • The rotary encoder can count the number of pulse output during rotation in the positive direction and reverse direction through the rotation and this rotation counts are not limited.
  • With the key on the rotary encoder, you can reset to the initial state, that is, counting from 0.
  • Package Content: 10 x Rotary Encoder Module, 5 x Black Knob, 5 x Silver Knob, 1 x 11.8" Female-Male Dupont Cables 50 PIN.
Check Stock

WSDMAVIS 1 Pcs Rotary Encoder E6B2 CWZ6C E6B2-CWZ6C 1024P/R DC 5-24V for OMRON

  • Type: 2pcs 360 Degrees Rotary Encoder Module, Model: KY-040, Working Voltage: 5V, Pulse Count Per Circle: 20.
  • Purpose: The rotary encoder can count the quantity of output pulse in the positive and negative direction rotation. The rotation counting is unlimited..
  • An incremental encoder is a rotating sensor that converts rotation displacement into a series of digital pulse signals. These pulses are used to control angular displacement..
  • The reading system usually uses differential mode to compare two different waveforms, but the phase difference is 180 degrees, so as to improve the quality and stability of the output signal..
  • With the button on rotary encoder, it can be reset to the initial state, that starts counting from 0..
Check Stock

LCD 12864 Graphic Smart Display Controller Board with Adapter and Cable for 3D Printer Ramps 1.4 RepRap 3D Printer Mendel Prusa

  • This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. Please note: With a SD Card base on back,SD card not included..
  • You can easy connect it to your Ramps board using the "smart adapter" included.After connecting this panel to your Ramps you don't need your pc any more, the Smart Controller supplies power for your SD card..
  • All actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller..
  • Print your 3D designs without PC, just with a g-code design stored on the SD card..
  • LCD 12864 graphic smart display module with blue backlight, small and light appearance, suitbale for copiers, fax machines, laser printers, industrial test equipment, networking..
Check Stock

Fielect 360 Degree Rotary Encoder Code Switch Digital Potentiometer EC11 5 Pins 20mm Shaft 5Pcs

  • [Specification]- Type: EC11 Encoder with Screw Thread.
  • [Rotary encoder]- By rotating the rotary encoder can be counted in the positive direction and the reverse direction during rotation of the output pulse frequency, unlike rotary potentiometer count, this rotation counts are not limited. With the buttons on the rotary encoder can be reset to its initial state, that starts counting from 0..
  • [Applications]- Rotary encoders are widely used in industrial controls, robotics, photographic lenses, computer input devices such as optomechanical mice and trackballs, controlled stress rheometers..
  • [Package Content]- 5pcs x Rotary Encoder Code Switch Digital Potentiometer.
Check Stock

Fielect 360 Degree Rotary Encoder Code Switch Digital Potentiometer EC11 7 Pins 10mm Shaft 5Pcs

  • [Specification]- Type: EC11 Encoder without Screw Thread.
  • [Rotary encoder]- By rotating the rotary encoder can be counted in the positive direction and the reverse direction during rotation of the output pulse frequency, unlike rotary potentiometer count, this rotation counts are not limited. With the buttons on the rotary encoder can be reset to its initial state, that starts counting from 0..
  • [Applications]- Rotary encoders are widely used in industrial controls, robotics, photographic lenses, computer input devices such as optomechanical mice and trackballs, controlled stress rheometers..
  • [Package Content]- 2pcs x Rotary Encoder Code Switch Digital Potentiometer.
Check Stock

Fielect 360 Degree Rotary Encoder Code Switch Digital Potentiometer EC11 7 Pins 10mm Shaft 2Pcs

  • [Specification]- Type: EC11 Encoder with Screw Thread.
  • [Rotary encoder]- By rotating the rotary encoder can be counted in the positive direction and the reverse direction during rotation of the output pulse frequency, unlike rotary potentiometer count, this rotation counts are not limited. With the buttons on the rotary encoder can be reset to its initial state, that starts counting from 0..
  • [Applications]- Rotary encoders are widely used in industrial controls, robotics, photographic lenses, computer input devices such as optomechanical mice and trackballs, controlled stress rheometers..
  • [Package Content]- 2pcs x Rotary Encoder Code Switch Digital Potentiometer.
Check Stock

Encoder Metal Gearmotor 12V DC High Speed 600RPM Gear Motor with Encoder for Robotics

  • ✔Product type: DC Gear motor with two-channel Hall effect encoder.
  • ✔Main Body Dimensions:74.8 x 25mm / 2.95in x 0.99in (L*D).
  • Out Shaft Dimensions: 11 x 4mm / 0.433 x 0.1575in (L*D) with 10 x 0.5mm / 0.39 * 0.017inches flat cut off.
  • ✔Single Output 120 Pulses Per Revolution: Gear Reduction Ratio: 1/10, Each Loop Output Pulses: 12PPR 10*12=120PPR.
  • ✔Wiring Diagram: Red - Motor power terminal (+).
  • ✔Application:Suit for Projects Such as Robotics,RC Car Model,Custom Servo, Arduino and 3D Printers,DIY Engine Toy..
Check Stock

10PCS 5 Pin Rotary Encoder+Washers+Nuts DC 5V EC11 Rotary Encoder Coding Switch Digital Potentiometer with Switch

  • [Specification]- Type: EC11 Encoder without Screw Thread.
  • [Rotary encoder]- By rotating the rotary encoder can be counted in the positive direction and the reverse direction during rotation of the output pulse frequency, unlike rotary potentiometer count, this rotation counts are not limited. With the buttons on the rotary encoder can be reset to its initial state, that starts counting from 0..
  • [Applications]- Rotary encoders are widely used in industrial controls, robotics, photographic lenses, computer input devices such as optomechanical mice and trackballs, controlled stress rheometers..
  • [Package Content]- 5pcs x Rotary Encoder Code Switch Digital Potentiometer.
Check Stock

Encoder Metal Gearmotor 12V DC High Speed 130RPM Gear Motor with Encoder for Arduino and 3D Printers

  • ✔Product type: DC Gear motor with two-channel Hall effect encoder.
  • ✔Main Body Dimensions:74.8 x 25mm / 2.95in x 0.99in (L*D).
  • Out Shaft Dimensions: 11 x 4mm / 0.433 x 0.1575in (L*D) with 10 x 0.5mm / 0.39 * 0.017inches flat cut off.
  • ✔Single Output 540 Pulses Per Revolution: Gear Reduction Ratio: 1/45, Each Loop Output Pulses: 12PPR 45*12=540PPR.
  • ✔Wiring Diagram: Red - Motor power terminal (+).
  • ✔Application:Suit for Projects Such as Robotics,RC Car Model,Custom Servo, Arduino and 3D Printers,DIY Engine Toy..
Check Stock

Bemonoc Encoder Metal Gearmotor 12V DC Low Speed 60 RPM Gear Motor with Encoder for Arduino and 3D Printers

  • ✔Product type: DC Gear motor with two-channel Hall effect encoder.
  • ✔Main Body Dimensions:74.8 x 25mm / 2.95in x 0.99in (L*D).
  • Out Shaft Dimensions: 11 x 4mm / 0.433 x 0.1575in (L*D) with 10 x 0.5mm / 0.39 * 0.017inches flat cut off.
  • ✔Single Output 1176 Pulses Per Revolution: Gear Reduction Ratio: 1/98, Each Loop Output Pulses: 12PPR 98*12=1176PPR.
  • ✔Wiring Diagram: Red - Motor power terminal (+).
  • ✔Application:Suit for Projects Such as Robotics,RC Car Model,Custom Servo, Arduino and 3D Printers,DIY Engine Toy..
Check Stock

CUI Inc AMT102-V AMT10X Series 3.6 to 5.5 V 2-8 mm Open Center Capacitive Encoder Switch Kit - 1 item(s)

  • [Specification]- Type: EC11 Encoder with Screw Thread.
  • [Rotary encoder]- By rotating the rotary encoder can be counted in the positive direction and the reverse direction during rotation of the output pulse frequency, unlike rotary potentiometer count, this rotation counts are not limited. With the buttons on the rotary encoder can be reset to its initial state, that starts counting from 0..
  • [Applications]- Rotary encoders are widely used in industrial controls, robotics, photographic lenses, computer input devices such as optomechanical mice and trackballs, controlled stress rheometers..
  • [Package Content]- 10pcs x Rotary Encoder Code Switch Digital Potentiometer.
Check Stock

BIQU LCD 12864 Version Graphic Smart Display Controller Module with Adapter and Cable for RAMPS 1.4 Reprap 3D Printer Kit

  • 2560 control board: The board is a microcontroller board based on the 16AU .It has 54 digital input/output pins (of which 14 can be used as PWM....
  • RAMPS 1.4: RAMPS interfaces an for Arduino with the powerful for Arduino platform and has plenty room for expansion. The modular design includes plug....
  • LCD 12864 with Controller: This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You....
  • A4988 driver module: A4988 Stepper Motor Driver Board is a breakout board for Allegro?ˉs A4988 DMOS Microstepping Driver with Translator and....
  • Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it....
Check Stock