Reviews Dualshock Thumbstick Replacement

12Pcs Trimmer Potentiometer Sensor Replacement for Xbox One,PS3,PS4 Switch Pro Controllers,Trim Pot Resistors Repair Parts for Thumb Stick Analog Joystick

  • Useful:The 3Pin trimmer potentiometer sensor needs to be replaced when the controller has the problem of creeping, stuttering, a blind spot, a dead spot, a dead zone or wouldn't center after years of wear and tear.Soldering the unit with only 3 prongs will be much more easier than replacing the 14Pin joystick assembly..
  • Used for:The trim pot resistor is OEM repair parts, the same model as the one in your controller. The genuine replacement sensor is to ensure accuracy and prolong lifespan. replacement for the wireless controllers below: PS3.
  • PS4 DualShock4 series (PS4, PS4 Slim, PS4 Pro).
  • Xbox One series (Xbox One, One S, One X and Elite).
  • Note:Make sure you have basic soldering skills and some soldering supplies like an electronics solder iron and small gauge solder. Use a pair of pliers to separate the problem sensor off the thumbstick component. A metal pick helps to clear the holes in the PCB. Re-soldering the new unit in is a breeze. Just remember to use flux and keep the iron's tip well tinned..
  • Package include: 12Pcs potentiometer sensor modules for games controller joystick..
Check Stock

Deal4GO 2 Pack OEM Replacement Thumbsticks Concave Analog for Xbox one Controller PS4 Joysticks Thumb Sticks Pink

  • NEW and ORIGINAL from Xbox one OEM Factory that has never been used..
  • Compatible with Xbox One /Xbox One S/Xbox One X/Dualshock 4 Controllers. (NOT FIT for Xbox Elite Controller).
  • Require technical internal fitting, Controller must be opened to install..
  • These thumbstick will fit for Xbox One controllers without any modification, ideal for replacing warn or damaged thumb Grips..
  • Each pack come with 2x Thumbsticks (Pink), Enough for ONE controller..
Check Stock

16 Pcs Colorful Replacement Thumbsticks (Analog Sticks) for Xbox 360 Controller

  • Analog joystick replacement for Xbox 360 Controller Thumbstick.
  • Four corners solder points to secure the stick to the PCB.
  • 2pcs Analog Joystick Replacement Part for Xbox 360 Controller Thumbstick.
Check Stock

Deal4GO 2-Pack OEM Replacement Thumbsticks Concave Analog Joystick for Xbox one Controller Dualshock 4 Controller Thumb Grips Dark Maroon

  • NEW and ORIGINAL from Xbox one OEM Factory that has never been used..
  • Compatible with Xbox One /Xbox One S/Xbox One X/Dualshock 4 Controllers. (NOT FIT for Xbox Elite Controller).
  • Require technical internal fitting, Controller must be opened to install..
  • These thumbstick will fit for Xbox One controllers without any modification, ideal for replacing warn or damaged thumb Grips..
  • Each order comes with 2x Thumb Grips (Dark Maroon), Enough for ONE controller..
Check Stock

Bullet Buttons Thumbstick Replacement Parts, 6Pcs/Kit Aluminum Alloy Bullet Buttons & Bullet Joystick Thumbstick for PS4 Controllers

  • High quality Metal Aluminum Joystick Thumbstick thumb grips replacement & Bullet Buttons & D-pad replacement Kits..
  • Aluminum Joystick & Buttons provide unique feeling and comfort, and better game experience..
  • To replace the buttons on the controller, you need to open the controller shell with screwdriver and remove origianl thumbstick, buttons, D-pad and then install the new kit..
  • Stable and great performance makes you operate smoothly in the game..
  • Brand new and high quality, good replacement parts especially designed for Playstation 4..
Check Stock

Linkstyle Switch Joystick Replacement, 3D Analog Joystick Analog Thumb Stick, 6PCS Switch Lite Left/Right Joysticks Rocker with 6PCS Thumbstick Caps for Nintendo Switch and Joycon Controller

  • 6× 3D JOYSTICKS: Upgrade replacement joysticks to work for Switch left/right Joycon joystick. Repair wore, out of control, insensitive analog joystick..
  • DURABLE: Made of high-quality material that wear-resistant, safe and comfortable, one replace long use. Box organizer design is convenient to carry or store..
  • EASY INSTALLATION: No need for complicated operations, easy and successful installation. Please note that after installation, use the Switch settings to set the calibration joystick..
  • THUMBSTICK PROTECTION CAPS: Come with 6 x thumbstick caps that can protect your joystick from scratches and damage. Enough quantity to meet your replacement needs and share with friends..
  • WAHT YOU GET: 6x analog joystick replacements for switch/switch lite,6x thumbstick cover caps,1x organizer case. If you have any questions about the analog joystick replacement, please feel free to contact us..
Check Stock

ElecGear 4X Replacement Joystick (EL2 FU 10K) for PS4 / PS3 Wireless Controller, Analog Stick Controller Sensor Assembly Thumbstick Module for Playstation

  • [EL2 FU 10K for PS4/PS3 Controller] – 4x replacement analog joystick was found in some PS4 DualShock 4 came with PlayStation 4 Pro, and some PS3 controllers also use this version. The thumbstick module was made by Favor Union (FU). The stick controller comes with 10KΩ trimmer potentiometers in orange.
  • [Compatibility] – The 14 prongs were positioned as the same as ALPS edition. Technically, the whole unit is interchangeable with EL1 ALPS 10K used in PS4 controllers, and other brands like ‘Scuf’ and ‘Razer Raiju Ultimate’ with ALPS joysticks inside. However, the trim pot resistor alone is not interchangeable with ALPS edition.
  • [Additional Resistor] – Complicated moving mechanism and daily wear and tear finally caused drifting. Even new sensors cannot be 100% balanced. Calibrating in controller settings might not work. We packed 10x correction resistors to solve the potential problem in hardware level. Solder one or two paralleled tiny resistors onto the potentiometer at the opposite direction against drifting. It will help correct 3 to 5 degrees drifting.
  • [When to replace] – The analog joystick needs to be replaced when your controller has the problem of drifting, creeping, stuttering, a blind spot, a dead spot, a dead zone, no react....
Check Stock

Rechargeable Batteries for PS4 Pro Dualshock Controller, FARSAIL 3-Pack 2000mAh LIP1522 PS4 Battery Replacement with Big and Small Plug for Playstation 4 PS4 Dualshock 4 Wireless Controller

  • ‍♂️【Replacement for Model/Part Numbers】Replacement for LIP1522/KCR1410 Battery.Compatible with 1st gen DualShock 4 and 2nd gen DualShock 4 V2 :CUH-ZCT1E,CUH-ZCT1H, CUH-ZCT1H/B, CUH-ZCT1H/R, CUH-ZCT1U and Playstation 4 Slim PS4 pro Dualshock 4 CUH-ZCT2U 2016 Playstation 4 Controller.
  • ‍♂️【Noted】This battery has two connectors. The bigger plug width is 4.5mm, the smaller one width is 3.5mm. While the batteries type of Dualshock 4 V1 and V2 are the same, the connectors are different. Make sure you get the right one. For controller model number begin with CUH-ZCT1, you need the large connector type. Units listed as CUH-ZCT2 have the smaller plug. The model number is printed on the sticker on the back of the controller..
  • 【Battery Specification】Volts: 3.7V, Capacity: 2000mAh. Comes with 2 x Replacement Battery For PS4 + 1 x Tool Set.You could watch YouTube videos for installation instructions.Please use the plastic tool gently. If you think our tools is not convenient to use,you could use your own tools.
  • ‍♂️【Long Battery Life】Premium Grade A cells for longer battery lifespan (number of recharge cycles) with no memory effect..
  • ‍♂️【Quality & Safety Guarantee 】Pickle Power ps4 controller battery are CE certified, tested ....
Check Stock

ElecGear 8X ALPS 10K Replacement Trimmer Potentiometer for PS4, Xbox One, Elite, Switch Pro Wireless Controllers, Trim Pot Resistor Thumbstick Module Sensor for ALPS Analog Joystick

  • ...er sensor needs to be replaced when the controller has the problem of creeping, stuttering, a blind spot, a dead spot, a dead zone, or it wouldn't center after years of wear and tear. De-soldering the unit with only 3Pins will be a lot easier than replacing the entire joystick with as many as 14 prongs.
  • [Reminder of Replacement] – Use a pair of pliers to separate the problem sensor off the joystick module. Try to replace the wiper first, see if it works. De-solder the sensor off the PCB. A metal pick helps to clear the holes. Soldering the new unit in is a breeze. Remember to calibrate the new control sticks in settings.
Check Stock

3.7v 1800mAh LiPo Battery for Sony DualShock 4 PS4 Controller Battery Replacement (Cuh-zct2u Battery_1 Pack)

  • Compatible with the Following Sony Playstation 4 PS4 Dualshock 4 Wireless Controller Models: CUH-ZCT1E, CUH-ZCT1H, CUH-ZCT1H/B, CUH-ZCT1H/R, CUH-ZCT1U (No Light Bar on Touchpad). PLEASE NOTE: THIS BATTERY IS NOT COMPATIBLE WITH 2016 (OR NEWER) DUALSHOCK 4 CONTROLLERS DUE TO THE BATTERY CONNECTOR BEING DIFFERENT. PLEASE FIRST VERIFY YOUR CONTROLLER'S MODEL NUMBER (ON BACK LABEL) MATCHES THE LISTED COMPATIBLE MODELS TO ENSURE THAT THIS IS THE CORRECT REPLACEMENT BATTERY BEFORE PURCHASE..
  • Non-OEM Replacement for the Following Battery Sony Model/Part Numbers: LIP1522 (OLDER MODEL ONLY)..
  • High Capacity 3.7V 1300mAh 4.8Wh Lithium-ion Rechargeable Battery Pack..
  • 1 Year Replacement Warranty. MPF Products is a Registered Trademark..
Check Stock

Mcbazel 2 Pack Controller 3D Analog Joystick Thumb Sticks Replacement Repair Parts for Xbox One Elite 2

  • - Replacement 3-pin analog stick for Xbox One Elite 2 controller..
  • - Fix for problems like stick drift, creeping, stuttering, blind spots, dead zones, no click, non-centered, broken, and loose joysticks..
  • - Compatible with Xbox One Elite 2 controller only (NOT PS4 Dualshock 4/ Dualshock 3 SixAisx / Xbox One / Wii U Gamepad Controller)..
  • - Package includes: 2 x 3-Pin 3D Analog Joystick.
Check Stock

BC Racing BR Series Coilovers compatible with 97-13 Chevrolet Corvette C5/C6

  • ... battery protection module to prevent Overcharge, over discharge and short circuit..
  • ➤ The battery fits Sony PlayStation 3 DUALSHOCK 3 PS3 controller model CCECHZC2E series, CCECHZC2U series bluetooth wireless controller, and for playstation gold wireless headset battery replacement..
  • ➤ PS3 controller battery replacement, the LIP1859 battery capacity is 3.16 times that of the original Sony PS3 wireless controller battery LIP1359 (570 mAh), So,this battery is obviously increases the battery life of the PS3 controller and to get a better experience is..
  • ➤ This LIP1859 battery fits replacement for Playstaion gold wireless headset battery, and compatible with PS4 Dualshock 4 Wireless Controller,fits models is CUH-ZCT1E, CUH-ZCT1H, CUH-ZCT1H/B, CUH-ZCT1H/R, CUH-ZCT1U.
  • ➤ --- How to replace the battery for Sony controller or Playstation gold wireless headset it? - - - If you not sure how to replace it, you can to watch some the video of how to replace on YouTube..
Check Stock

Tectra 1200mAh LIP1522 Replacement Li-ion Battery + Tools for Sony PS4 Playstation 4 Wireless Dual Shock Controller CUH-ZCT1E CUH-ZCT1U

  • ★ 1200mAh 3.7v lithium battery replacement for Sony PlayStation 4,DualShock 4 Ps4 controller battery replacement PS4 bluetooth wireless controller FIRST GENERATION old version PS4 controller CUH-ZCT1E, CUH-ZCT1H, CUH-ZCT1H/B, CUH-ZCT1H/R and CUH-ZCT1U..
  • ★ PS4 controller battery upgrade, The battery capacity of 1200mAh is twice that of the original Sony PlayStation 4 wireless controller battery LIP1522 (1000mAh), after upgrade the battery, continuous working time of the controller is obviously prolonged..
  • ★ PLEASE NOTE: This battery IS NOT compatible with the 2016 (or newer) CUH-ZCT2 or CUH-ZCT2U Dualshock 4 Controller due to it having a different battery connector. Please first check your controller's model number to ensure that this is the correct replacement battery.
  • ★ How to replace the ps4 controller‘s battery? - If you have no idea, you can watch some videos about how to replace it on YouTube,【Video Keyword: PS4 controller battery replacement】Thank you!.
Check Stock