Reviews Dc Motor Driver

HiLetgo L298P DC Motor Drive Module L298P DC Motor Drive Shield H-Bridge Drive Expansion Board High-Power DC Stepper Motor Controller for Arduino

  • Driven part of the input voltage VS: VIN Input 6.5 ~ 12V, PWRIN 4.8 ~ 35V input..
  • The L298P shield DC motor driver has PWM speed control mode.
  • Adopt dedicated high-power motor driver chip L298P which can directly drive two DC motors with drive current up to 2A..
  • Stack design can be directly plugged into the Arduino, easier to use..
Check Stock

Motor Controller, DROK PWM DC Motor Speed Controller 10-50V 60A High Power HHO RC Driver PWM Controller Module 12V 24V 48V 3000W Extension Cord with Switch

  • Parameter: DROK DC motor controller operating voltage range is DC 10-50V, max rated current is 60A, control power range is 0.01-3000W, working temperature range of -20℃-40℃..
  • High-end Configuration: Our motor driver control board uses PWM modulation system to adjust light & speed. In addition, it is designed with radiators to doing heat dissipation created by MOS tube..
  • Convenient Speed Control: With wires to connect potentiometer and regulation switch to control the speed, it is convenient to use..
  • Low Quiescent Current: our speed regulation module is designed with low quiescent current 0.04A(When the working voltage is DC10V-50V, the quiescent current cannot exceed 40mA)..
  • Wide Application: our motor driver control board can be applied to universal DC brush motor speed regulation.
  • production line conveyor belt speed regulation.
Check Stock

DC Motor Driver, DROK L298 Dual H Bridge Motor Speed Controller DC 6.5V-27V 7A PWM Motor Regulator Board 12V 24V Electric Motor Control Module Industrial 160W with Optocoupler Isolation

  • DROK DC motor driver input voltage range is DC 6.5V-27V, can be input DC 12V or 24V, rated output current of each port is 7A, total output power is 160W..
  • STRONG DRIVE: the motor controller board adopts dual H bridge, can drive two DC motors at the same time..
  • FORWARD and REVSERSELY ROTATE: the IN1, IN2/IN3, IN4 port can control forward or reverse motor rotation..
  • PWM SPEED CONTROL: enable signal terminal (ENA) input PWM can regulate speed, PWM frequency range 0-10KHZ..
  • UNDER VOLTAGE PROTECTION: the motor driver module is with under voltage protection to prevent instantaneous large current from damaging the module..
Check Stock

8PCS L298N Motor Drive Controller Board Dual H Bridge DC Robot Stepper Motor Compatible with Ardu-ino Electric Projects, Smart Car Robot

  • Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip, Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors..
  • The L298N driver module, using L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface, you can chip circuitry to 5V power supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential..
  • Terminal driver part of the supply area VMS: +5V ~ +35V.
  • Drive part of the peak current Io: 2A / Bridge.
  • Logical part of the terminal power supply range Vss :4.5-5 .5V.
  • Logical part of the operating current range: 0 ~ 36mA.
  • The control signal input voltage range: 4.5-5.5V low 0V high.
  • To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.
  • High working power to 46v, large current can reach 3A MAX and continue current is 2A, power to 25w..
  • Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability, large capacity filter capacitance,afterflow protection diode, more stable and reliable..
Check Stock

RATTMMOTOR 400W Blushless CNC Air Cooled Spindle Motor ER8 12000RPM + 600W Blushless Spindle Motor Driver LCD Panel without Hall + 55mm Clamp Mount for CNC Router Milling Machine

  • 【Brussless Spindle Motor】Power: 400W.
  • Note: Please see clearly that this spindle motor output shaft is with ER8 collet,and output shaft is complete shaft, can't be exchanged to ER11, ER16....
  • 【Brussless Spindle Motor Driver】Maximum driver power: 600W.
  • Maximum driver motor running speed: 12000R/Min.
  • Brushless spindle driver（Model Name: NVBDL）is specialized for the ecomomic engraving machine,it matchs with the brushless DC motor. With the....
  • The users can take down the panel from the main driver and install it on the controller cabinet.By the panel,you can set the parameter,control motor....
Check Stock

sb components Raspberry Pi Pico Board with Pico Motor Driver HAT Connects 2 DC and 1 Stepper Motor DC Motor Control Module for Raspberry Pi Pico, Raspberry Pi Pico Kit

  • Raspberry Pi Pico is Raspberry Pi's first microcontroller board, designed especially for physical computing.
  • It can be easily reprogrammed over USB from a Raspberry Pi or other computer using the C/C++ SDK or the official MicroPython port.
  • Pico Driver Motor HAT is a DC motor control module that is powered by one H-bridge IC L293D with the motor input supply range 6 V-24 V.
  • Pico Driver Motor HAT is specifically made to work with the Raspberry Pi Pico Board.
Check Stock

Kiro&Seeu L293D DC Motor Drive Shield Stepper Motor Drive Shield Expansion Board Compatible with Arduino Duemilanove Raspberry Pi

  • This is a commonly used DC motor drive module, using a small current 293 chip DC motor driver chip..
  • Using this chip you can use DC motors and power supplies of up to 10 Volts, that some pretty big motors and the chip can supply a maximum current of 600mA per channel..
  • Tested compatible for Arduino Mega, Diecimila & Duemilanove..
  • 2 interface for 5V Servo connected to the Arduino's high-resolution dedicated timer - no jitter..
  • Multi-function, easy to operate, a strong driver library support and feature updates..
Check Stock

MINARIK MM23001C 0-90/0-180V-DC 1/4-2HP 5A AMP DC MOTOR DRIVE D506404

  • Motor Driver: 9V-42V DC power supply, H bridge bipolar constant phase flow drive. The maximum 4.0A of the eight kinds of output current..
  • Motor Driver: Energy-saving semi-automatic current lock function, built-in temperature protection and over current protection.The largest 32 subdivision of the 6 models are optional..
  • Package: TB6600 stepper motor driver + nema 17 stepper motor + mounting bracket + inner hexagon spanner + M3/M4 screws.
  • Strive for 100% service satisfactory, any question or problem please do not hesitate to contact us, we are always happy to help..
Check Stock

Befenybay 50mm Effective Travel Length Mini Linear Rail Guide Lead Screw T6x1 with NEMA11 Stepper Motor for DIY CNC Router Parts X Y Z Linear Stage Actuator

  • DURABLE: The slide screw stepper motor made of high quality meterial, strong and durable in use, working voltage DC 9-12V..
  • MAXIMUM LINEAR SPEED: The maximum linear speed of lead screw worm drive stepper motor is 25mm per second..
  • APPLICATION: The DC 12V stepper motor widely used for small devices such as medical equipment, laser engraving machine, etc..
  • PRODUCT PARAMETER: The linear screw stepper motor moves 0.25mm for one step, can use microstep driver if need smaller..
  • NOTE: The stepper motor need a A4988 driver(not included) to drive, can not directly connect to power..
Check Stock

DORHEA PWM DC Motor Speed Controller DC 10-55V 24V 36V 48V 60A Stepless Motor Speed Controller with Adjustable Potentiometer Forward-Brake-Reverse Switch and LED Digital Display DC Brush Motor

  • Motor speed controller input supply voltage: DC 10V-55V.
  • The motor speed controller is an aluminum case, very strong to prevent damage, holes on its side and top which are helpful for heat dissipation..
  • The pmw dc motor speed controller come with switch function. High power speed controller switch which is much more adaptable and conveniently change the motor direction..
  • The stepless motor knob adjusts the motor speed from 0% ~ 100% smoothly with LED display is accurate to show 0 ~ 100% of the motor speed..
  • The input voltage of PWM motor speed controller should be equal to the rated voltage of the motor within 10-55V,or it will be burnt, the dc motor driver can be used to brush motor speed regulation, light dimming regulation in the DC circuit.Note: The motor cannot be used in electric vehicles..
Check Stock

PWM DC Motor Speed Controller, DC10-55V/40A Max 60A Stepless DC Motor Speed Controller with Forward-Brake-Reverse Switch Adjustable Potentiometer and LED Display,Continuous Current 40A

  • ...or speed from 0% ~ 100% smoothly. And with LED display is accurate to show 0 ~ 100% of the motor speed. The input voltage of PWM motor speed controller should be equal to the rated voltage of the motor within 10-55V,or it will be burnt.Do not reverse the positive and negative poles！.
  • 【Application】 The dc motor driver can be used to brush motor speed regulation, light dimming regulation in the DC circuit.Note: The motor cannot be used in electric vehicles..
Check Stock

G-Hubble Ender 3 Dual Z Axis Upgrade Kit with Lead Screw Stepper Motor 3D Printer Accessories Parts for Creality Ender 3/Ender 3 Pro/Ender 3 V2/Voxelab Aquila

  • Motor Driver: 9V-42V DC power supply, H bridge bipolar constant phase flow drive. The maximum 4.0A of the eight kinds of output current..
  • Motor Driver: Energy-saving semi-automatic current lock function, built-in temperature protection and over current protection.The largest 32....
  • Package: TB6600 stepper motor driver + nema 17 stepper motor + mounting bracket + inner hexagon spanner + M3/M4 screws.
  • Strive for 100% service satisfactory, any question or problem please do not hesitate to contact us, we are always happy to help..
Check Stock

4 Axis CNC Nema23 Stepper Motor Dual Shaft 425oz-in 3A+FMD2740C Driver 40V 4A+400W 36V Power Supply+USB CNC Breakut Board Controller Kit For CNC Router

  • ♞【Product】4 Axis nema23 stepper motor driver usbcnc controller kit.
  • Wirings: "A+"=Red / "A-"=Green / "B+"=Yellow / "B-"=Blue.
  • ♞【Driver】FMD2740C driver Voltage: DC12-50V.
  • Current: rated maximum output reaches: 4A.
  • Subdivision precision 2 8 16 32 64 128 10 20 optional.
  • ♞【4 Axis USBCNC Breakout Board】USB port,only support USB CNC Software,not fit for Mach3 software.Our parcel include a CD,it include the user manual and USBCNC software.
  • ♞【400W 36V 11A DC Switching power supply】Please flip the side input voltage selector switch,Input: AC110V-120V or AC220V-240V.
  • 【Computer system 】Support Win XP/7/8/10,if you can not get the activation code on Win 10,pls let us know,we will help you to solve it..
Check Stock