Reviews Cylinder End

CDHPOWER Super Motor PK80 Replaement with Iron Sleeve Cylinder 49mm Top End Cylinder Set and Bottom End Crank Set for 2 Stroke kit 66cc/80cc

  • CDHPOWER Super pk80 motor Replaement:Iron Sleeve Cylinder 49mm:Top End Cylinder Set and Bottom End Crank Set for 2 stroke kit 66cc/80cc pk80 motor kit.
  • High hole Piston kit installed well inside of cylinder and Long connecting rod AF80 or zmn80.
  • The casting cylinder head increases the horse power and this greatly cools off the engine. Would result better performance and longer life for your 2 Stroke Bicycle Engine. Casting cylinder head Height Max:51mm-52mm.
  • Clear up the cylinder transfer ports before assembling maybe some rough slag inside which maybe break off and cause the jamming of pistons and cylinders.
  • fully attention on screwing cylinder to the end bottom,DO NOT screw M8 bolts tightly that maybe cause drill through the end bottom so add some gasket or washer on head is better way to prevent it happen.
  • Attention on piston ring if put the piston out of cylinder, the piston rings are weak, better with right way install piston kit to cylinder.
Check Stock

PAGOW Spark Plug Boot Wire Removal Tool Ignition Coil Puller for Volkswagenn Audi VW Hand Install Repair Tool

  • Best Compatibility: The spark plug wire puller installer can perfect match with Volkswagen and Audi vehicles with standard prong plug caps on each side (not recommended for non-VW/Audi plug leads). Volkswagen – New Beetle 2.0 engine AZJ (AEG), Golf IV & V 1.6 engine (AVH), 1993-2005 2.0L 4 cylinder (AZG), 1998-2006 1.8L 4 cylinder (BBW), 2006 and later 2.0L 4 cylinder turbo (BDC).
  • Audi – 1998-2006 1.8L 4 cylinder turbo (BEV), 2006 and later 2.0L 4 cylinder turbo (BGD)..
  • Size Inforamtion: The size of spark plug boot removal tool kit: 12.6inch (32cm) overall length, 3.75inch x 0.4inch x 1.2inch (9.5cm x 1cm x 3cm) handle, 9.25inch (23.5cm) shaft, 2.2inch x 0.8inch (5.6cm x 2cm) boot end..
  • Wide Applications: The spark plug puller tool suitable for Bora, Mercedes, Smart, and other Volkswagen and Audi vehicles with similar engines and standard prong plug caps on each side..
  • Easy to Use:Perform spark plug change when engine is cold to prevent the heads from stripping. After pulling the plugs, we recommend applying lubrication to make the job easier. When installing wires, refrain from pushing too hard without the tabs aligned on the tool to prevent the boot end from spreading and getting stuck..
  • Material:The handle of ignition coil puller is made of hard p....
Check Stock

CDHPOWER PK80 Motor Replacement of Top End Cylinder Set and Bottom End Crank Set for 2 Stroke kit 66cc/80cc

  • PK80 MOTOR REPLACEMENT PARTS ONLY. piston kit is installed well inside of cylinder already.
  • better adjusting Clutch a little before riding.
  • High hole Piston and Long connecting rod.
  • Clear up the cylinder transfer ports before assembling maybe some rough slag inside which maybe break off and cause the jamming of pistons and cylinders.
  • fully attention on screwing cylinder to the end bottom,DO NOT screw M8 bolts tightly that maybe cause drill through the end bottom so add some gasket or washer on head is better way to prevent it happen.
  • Attention on piston ring if put the piston out of cylinder, the piston rings are weak, better with right way install piston kit to cylinder.
Check Stock

MOOSUN Cylinder Piston Gasket Top End Kit Fits 1988-2006 Yamaha Blaster 200 YFS200

  • 【BLASTER 200 CYLINDER TOP END KIT】Compatible with 1988-2006 Yamaha Blaster 200 YFS 200.
  • 【SPECIAL FUNCTION】MOOSUN Blaster 200 Cylinder replacement piston sets engineered from premium materials to provide exceptional service life and....
  • 【BLASTER 200 CYLINDER HEAD PISTON FEATURE】Cylinder piston set is the heart of engine. MOOSUN Cylinder has been factory honed and deburred to help....
  • 【PART NUMBER】2XJ-11111-00-00, 2XJ-11311-02-00,2XJ-11181-00-00, 2XJ-11631-01-97, 3JM-11351-02-00, 3JM-13621-00-00, B8E-S0000-00-00,....
  • 【CYLINDER PISTON RING GASKET KIT COMES WITH】1 x Cylinder, 1 x Piston, 1 x Piston Rings, 1 x Wristpin, 2 x Circlips, 1 x Needle Bearing, 1 x Head....
Check Stock

Cylinder Top End Rebuild Kit for 1988-2006 Blaster 200 YFS 200 Engine Piston Gasket Kit

  • 【Blaster 200 Cylinder Top End Kit】Fit for 1988-2006 Yamaha Blaster 200 YFS 200.
  • 【Function】Blaster 200 Cylinder replacement piston sets engineered from premium materials to provide exceptional service life and reliability.....
  • 【Blaster 200 Cylinder Head Piston Feature】Cylinder piston set is the heart of engine. OBUYTO Cylinder has been factory honed and deburred to help....
  • 【Part Number】2XJ-11111-00-00, 2XJ-11311-02-00,2XJ-11181-00-00, 2XJ-11631-01-97, 3JM-11351-02-00, 3JM-13621-00-00, B8E-S0000-00-00,....
  • 【Cylinder Piston Ring Gasket Kit Comes With】1 x Cylinder, 1 x Piston, 1 x Piston Rings, 1 x Wristpin, 2 x Circlips, 1 x Needle Bearing, 1 x Head....
Check Stock

Ambienceo 26” 28” Black 2 Stroke 50cc 80cc Cycle Bicycle Gas Motorized Gasoline Engine Motor Kit CDI Air Cooling For Mountain and Road Bike 80cc Silver

  • CDHPOWER LD90 Cylinder Body w/Piston Kit.
  • Compatible with bottom end of all brand 2 stroke gas motor kit 66cc/80cc/pk80/LD80/LD90 including other....
  • New pk80 upgraded cylinder with piston kit, the piston kit is installed well inside of cylinder already.Excluding cylinder head..
  • Cylinder head gasket and cylinder body gasket are included.
  • The LD90 Cylinder Body and piston kit can be replacement of most 2-stroke gas motor engine such as pk80/LD80/LD90.
  • piston pin:10mmx39mm.This is a high hole piston for a 40mm stroke but with 48mm bore..
Check Stock

TOP NOTCH PARTS CYLINDER PISTON GASKET OIL AIR FILTER TOP END KIT SET FITS YAMAHA RAPTOR 350 2004 2005 2006 2007 2008 2009 2010 2011

  • Replaces OEM Part # 1UY-11310-03-00, 1UY-11631-Y0.
  • CYLINDER PISTON GASKET OIL AIR FILTER TOP END KIT SET FITS YAMAHA RAPTOR 350 2004 2005 2006 2007 2008 2009 2010 2011.
  • PURCHASE INCLUDES: CYLINDER BLOCK. PISTON. PISTON RING KIT. PISTON PIN. CIRCLIPS. CYLINDER HEAD GASKET. PAPER CYLINDER BLOCK GASKET CHAIN TENSIONER,....
Check Stock

66mm 195cc Cylinder Head Piston Gasket Top End Kit Set for Yamaha Blaster 200 YFS 200 1988-2006 2XJ-11111-00-00 2XJ-11311-02-00

  • 【Wide Applications】This cylinder piston gasket top end kit replacement fit for Yamaha Blaster 200 YFS200 1988-2006.
  • 【Excellent Design】Complete standard sized replacement cylinder kit. Cylinder bore and stroke 66.00mm x 57.00mm. Cylinder displacement 195cc /....
  • 【Package Contents】Cylinder,Cylinder Head,Piston,Piston Pin,Piston Rings,Circlips,Needle Bearing,Head Gasket,Base Gasket,Valve for Seat....
  • 【Part Number】2XJ-11111-00-00,2XJ-11311-02-002XJ-11181-00-00 3JM-11351-02-00,B8E-S0000-00-00 2XJ-11631-01-97,4L0-11633-00-00,3JM-13621-00-00.
  • 【Premium Quality】Made of high-strength aluminium alloy material,can effectively improve heat、pressure and corrosion resistance.Heavy duty metal....
Check Stock

MSA Non-Electronic Cylinder Holder Assembly For GALAXY(R) GX2 Automated Test System

  • Used With Galaxy GX2 Automated Test System Only.
  • Lighted Cylinder Band for Low Gas and Expiration Date Warning Display.
Check Stock

CDHPOWER 2 Stroke LD90 Motor w/o CDI -Upgraded pk80 Motor Silver Color Engine-Gas Motorized Bicycle 66cc/80cc

  • CDHPOWER LD90 Motor w/o CDI and Excluding 2pcs anti vibration black rubber for the motor mount,upgraded pk80 motor.
  • better adjusting Clutch a little before riding..
  • Includinhg spark plug and piston kit；Excluding two head plug CDI Box ( Asin for two head plug CDI: B098Q988VJ ).
  • High hole Piston and Long connecting rod.
  • Clear up the cylinder transfer ports before assembling maybe some rough slag inside which maybe break off and cause the jamming of pistons and cylinders.
  • fully attention on screwing cylinder to the end bottom,DO NOT screw M8 bolts tightly that maybe cause drill through the end bottom so add some gasket or washer on head is better way to prevent it happen.
  • Attention on piston ring if put the piston out of cylinder, the piston rings are weak, better with right way install piston kit to cylinder.
  • FYI: the LD90 motor is compatible with all brand 2 stroke 66cc/80cc gas motor kit.
Check Stock

EWK Spark Plug Boot & Wire Removal Tool, Ignition Coil Puller for VW Audi T10112

  • 【 Work Smart 】 This spark plug boot removal Tool T10112 is a special tool for quickly remove the spark plug lead without destroying any component..
  • 【 Time Saver 】 The angled shaft fits well into narrow plug cavity with no manifold dismantling needed, reach the plugs on cylinder #2 and #3 smoothly..
  • 【 High Quality 】 Shaft and boot end are constructed from premium stainless steel for maximum strength and longevity. The ergonomically grip convenient to use..
  • 【 Applications 】 Volkswagen – New Beetle 2.0 engine AZJ (AEG), Golf IV & V 1.6 engine (AVH), 1993-2005 2.0L 4 cylinder (AZG), 1998-2006 1.8L 4 cylinder (BBW), 2006 and later 2.0L 4 cylinder turbo (BDC).
  • Audi – 1998-2006 1.8L 4 cylinder turbo (BEV), 2006 and later 2.0L 4 cylinder turbo (BGD). *Not recommended for non-VW/Audi plug leads..
  • 【 Excellent WorKing Experience】Durable products with 12+6 months warranty, reply within 24 hours, ship out within 24 hours to achieve fast delivery. Contact us if you need further assistance..
Check Stock

DOZYANT Gas Lift Cylinder, Office Chair Gas Lift Cylinder Replacement,Hydraulic Pneumatic Shock Piston Heavy Duty (450 lbs) Universal Size Fits Most Executive Chairs, Highest End Class 4

  • HEAVY DUTY Gas lift cylinder that holds great weights - tall center support column of the chair. Holds up to 450 lbs on most office, executive and computer chairs.Highest End Class 4 gas cylinder on market..
  • STANDARD CYLINDER DIAMETER: Outer cylinder: 2 inches, Inner cylinder: 1.1 inches. Please confirm the measurement before ordering..
  • SMOOTH & NOISELESS: Full 360 degree rotation, smooth and noiseless movements to all directions.
  • 5’’ STROKE FOR ADJUSTING CHAIR HEIGHT: Minimum length: 10 inches.
  • maximum length when fully extended: 15 inches.
  • EASY INSTALLATION : Can be installed easily with no additional screws required..
Check Stock

DOZYANT 8" Long Stroke Office Chair Gas Lift Cylinder Replacement,Hydraulic Pneumatic Shock Piston Heavy Duty (450 lbs) for Tall Person Universal Size Fits Most Executive Chairs, Highest End Class 4

  • 8″ STROKE FOR ADJUSTING CHAIR HEIGHT: Minimum length: 11.2 inches.
  • maximum length when fully extended: 22.5 inches.
  • HEAVY DUTY Gas lift cylinder that holds great weights – tall center support column of the chair. Holds up to 450 lbs on most office, executive and computer chairs. Highest End Class 4 gas cylinder on market..
  • STANDARD CYLINDER DIAMETER: Outer cylinder: 2 inches, Inner cylinder: 1. 1 inches. Please confirm the measurement before ordering..
  • SMOOTH & NOISELESS: Full 360 degree rotation, smooth and noiseless movements to all directions.
  • EASY INSTALLATION : Can be installed easily with no additional screws required..
Check Stock