Reviews Cross Assemblies

Cane Creek Headset Forty 40 Serie Bottom IS52/40 (Integrated)

  • Internal parts are cross-compatible across 1, 4 and 11 series.
  • Consistent stack heights across 1, 4 and 11 Series.
  • Bottom assemblies include bottom cup, sealed oxide bearing, and crown race.
Check Stock

Malone MicroSport Low Bed Kayak Trailer

  • Marine grade pre-galvanized steel frame, 12" galvanized wheels w/ sealed marine grade bearings.
  • 197 lbs. (base kayak trailer), 800 lb. capacity, 78" wide x 159" long, 78" coated steel cross rails.
  • Double leaf spring suspension, extra-long reinforced tongue with support skid and lift handle.
  • Pre-fitted electrical, mechanical, and hub assemblies, DOT-approved lighting & bearings.
  • Assembles in 3-4 hours, complete instructions included, 2" hitch, Five-year warranty.
Check Stock

CCC, French Press 5 Part Stainless Steel 3.75 Inch Wide Plunger Assembly For Flat Top 34 oz 8-Cup 1 Liter Coffee Press Replacement Part

  • [GOOD QUALITY MATERIALS] 304 GRADE Stainless Steel (SS) PLUNGER ROD with closed nut, cross plate with threaded stem, spiral plate, one 18/8 SS wire mesh filter with a SS plunging knob.
  • Try CCC's 34oz Replacement Glass - it's FIRE TOUGHENED with measures.
  • Also Filter Parts, Cross, Filter and Spiral plate assemblies.
  • and Pour Over options to use on your press carafe coming soon..
Check Stock

Durablow Fireplace Electronic IPI Pilot Ignition Control Module Replacement for Dexen 593-592, GM-6KA, Hearth Home Technologies HHT 350-M

  • ...irect fit, and replaces OEM. Verify your old module is bad before ordering. ▼ This IPI-6000 module is for intermittent pilot operation, controls LP & NG fireplaces. Operate your unit with an ON and OFF switch..
  • ▼ Other parts are NOT included - Wiring harness (593-590A), power supply (593-594A or 593-593A), Pilot assemblies (385-510A NG, 593-510A, 4021-025), Millivolt valve (6003, 705-500, 705-501, 593-500, 593-501)..
  • ▼ LEGAL DISCLAIMER: (1) The Brand name & Model # are for cross reference only. All Brands, Trademarks & Model # remain the property of their respective owners. (2) This equipment must be installed by qualified electrical technician or service personnel. (3) Disconnect power before servicing..
Check Stock

OTC Tools 5080A Leaf Spring Pin and Bushing Service Set (Truck Front)

  • Delivers 10 tons of hydraulic force to remove and install truck front spring eye bushing assemblies quickly and easily.
  • Services bushings with diameters from 1-1/4 inch through 1-7/8 inch and pin diameters from 7/8 inch through 1-1/8 inch.
  • Handles all popular OE and aftermarket components including Horton pin and bushing assemblies.
  • Service bushing assemblies in many cases without removing leaf spring hangers and spring assemblies from the vehicle.
  • All accessories are included except the hydraulic hand pump which must be purchased separately.
Check Stock

(5 Pack) Standard Threaded Brass Bowls - Lighting Fixture Spare Parts - Standard Decorative Bowls

  • For use with Standard Size Deacon Smith Lighting Fixture Assemblies and Spare Partsi.
  • Standard 1/8 IP Threads for use on most lighting fixtures and some assemblies.
  • Brass Spare Parts for Deacon Smith Assemblies.
  • Compatible with Deacon Smith Standard Conduit Downstems and Standard Decorative Parts.
Check Stock

Delphi FG1371 Fuel Module

  • Delphi fuel modules and pumps are designed to deliver an immediate, uninterrupted flow of fuel to the engine's fuel rail and injectors at the specified system pressure, resulting in more efficient operation.
  • Where required, fuel assemblies include integrated fuel level sensing components that deliver an accurate reading of the fuel level in the tank to the fuel gauge.
  • Delphi fuel pump assemblies are built with OE-validated parts and include OEM-grade wiring, electrical connectors and level sensor assemblies that deliver increased performance, durability and reliability over other aftermarket fuel pumps.
Check Stock

LMR-400/LMR400 Times Microwave Low Loss Coaxial Cable - PL259 UHF Male to UHF Male Connectors 50 Feet-CB Ham Radio Antenna - Made in The USA by Cable Assemblies Now

  • All Cable Assemblies Now Inc cable assemblies are MADE IN THE USA - we pride ourselves in making sure we provide all of our customers with the best quality product made with the highest quality materials.
  • WARRANTY on ALL Cable Assemblies made and mfg by Cable Assemblies Now Inc. have a limited 10 year warranty - Please do not hesitate to contact us for any questions or concerns.
  • We can guarantee that any cable under 1000MHz will have a Standing wave ratio plot of 1.25:1 at any frequency under 1000 MHz - We can also test return loss, insertion loss, phase angle, and use a Vector Network Analyzer to measure for both match and resonance..
Check Stock

iJDMTOY (2 Universal Sealed Rubber Housing Caps Compatible With Headlight Install Xenon Headlight Kit, LED Headlights Bulbs, Aftermarket Headlamp Retrofit, etc

  • This listing is for (2) universal sealed rubber housing caps.
  • Good for xenon LED conversion kits, aftermarket LED headlights, retrofit headlights, and many more of your retrofit lighting assemblies.
  • Seals your aftermarket retrofit LED assemblies and protects them from water condensation, moisture, dust, and other unwanted substances.
Check Stock

OTC 5285 1,650 lb. Capacity Air/Hydraulic Power Train Lift

  • OTC's 1,650 lb. capacity Powertrain Lift is perfect for handling engine and transmission assemblies, gas tanks, drive axle assemblies, engine/transaxle assemblies, electric vehicle batteries, and more.
  • Scissors-type design allows access to all 4 sides of a component for supreme accessability.
  • Two independent adjusting screws tilt the table 15 degrees side-to-side, or fore and aft and can be operated manually or with a non-impact air wrench.
  • Air/hydraulic operation via a foot control pump that features a flexible hose allowing movement around lift.
  • Features a 20 x 32 inch table, 8-inch high capacity swivel casters, a minimum height of 31-1/2 inches with a 74-1/2 inch maximum height, and a footprint that is 33 inches wide x 48 inches long.
Check Stock

Aftermarket Replacement 4 Pc Set Halogen Headlights & Signal Marker Lamps Compatible with 1999-2007 Sierra Pickup Truck Replaces 15199560 15199561 15850351 15850352

  • Good for xenon headlight conversion kits, aftermarket LED headlights, retrofit headlights, and many more of your retrofit lighting assemblies.
  • Seals your aftermarket retrofit LED assemblies and protects them from water condensation, moisture, dust, and other unwanted substances.
  • Made with high quality flexible rubber (+/- 3mm accommodation) that is ideal for retrofit lighting assemblies.
  • This listing is for 2 pieces of 95mm on the outer diameter size: To select the size of the cap you need, measure the outer diameter of your....
Check Stock

2-Pack AR-PRO 6” x 1.5” Flat Free Solid Rubber Wheel Assemblies - Replacement Hand Truck Wheels with Ball Bearings and 1/2” Bore Hole Diameter - Heavy-Duty Solid Rubber Wheels 132 lbs Load Capacity

  • AR-PRO 6” X 1.5” FLAT FREE SOLID RUBBER WHEEL ASSEMBLIES - These sets of flat-free wheel assemblies have nominal dimensions of 6 inches (outer....
  • REPLACEMENT HAND TRUCK WHEELS WITH BALL BEARINGS AND 0.5” BOREHOLE DIAMETER - These wheel assemblies come in different sizes, but these 6-inch tires....
  • HEAVY-DUTY SOLID RUBBER WHEELS WITH 132 LBS LOAD CAPACITY - Convenient and maintenance-free, these flat-free solid rubber tires and wheel assemblies....
  • HEAVY-DUTY SOLID RUBBER WHEELS WITH 132 LBS LOAD CAPACITY - The solid metal rims and hubs also have high resistance to impact cracks, making it highly....
  • SAFE AND COMFORTABLE RIDE - Say goodbye flats without saying goodbye to a smooth and comfortable ride. AR-PRO flat-free tires provide convenience,....
Check Stock

iJDMTOY (2 95mm Rubber Housing Seal Caps Compatible With Headlight Install Xenon Headlight Kit, Aftermarket Headlamp or Retrofit

  • Good for xenon headlight conversion kits, aftermarket LED headlights, retrofit headlights, and many more of your retrofit lighting assemblies.
  • Seals your aftermarket retrofit LED assemblies and protects them from water condensation, moisture, dust, and other unwanted substances.
  • Made with high quality flexible rubber (+/- 3mm accommodation) that is ideal for retrofit lighting assemblies.
  • This listing is for 2 pieces of 95mm on the outer diameter size: To select the size of the cap you need, measure the outer diameter of your headlight's rear flange. If you're under by 3mm of the cap size, we recommend going for the next size down.
Check Stock