Reviews Coupling Assemblies

8 Pack 1/4-20 X 7/8\ Long Hex Coupling Nut with Zinc Plate NCUP004C000STLZN

  • Coupling nuts are threaded fasteners for joining two male threads, most commonly threaded rod.
  • Coupling Nuts are used to make up long rod assemblies from shorter lengths of rods.
  • Country of Origin: Taiwan, Province Of China.
Check Stock

Lovejoy 6528 Size 1050 Grid Spacer Coupling Shaft Hub, Inch, 2.375\ Bore, 3500 in-lbs Nominal Torque, 0.625\ x 0.313\ Keyway

  • For use with Lovejoy 1000 series grid coupling assembly (sold separately).
  • Open-style shaft hub for horizontal- or vertical-style grid coupling assemblies.
  • Stamped steel for strength and durability.
  • Supports constant angular misalignment of up to 0.25 degrees.
  • Imperial unit measurements for industry consistency.
Check Stock

Lovejoy 6517 Size 1040 Grid Spacer Coupling Shaft Hub, Inch, 1.625\ Bore, 2000 in-lbs Nominal Torque, 0.375\ x 0.188\ Keyway

  • For use with Lovejoy 1000 series grid coupling assembly (sold separately).
  • Open-style shaft hub for horizontal- or vertical-style grid coupling assemblies.
  • Stamped steel for strength and durability.
  • Supports constant angular misalignment of up to 0.25 degrees.
  • Imperial unit measurements for industry consistency.
Check Stock

Lovejoy 6531 Size 1060 Grid Spacer Coupling Shaft Hub, Inch, 1.625\ Bore, 5500 in-lbs Nominal Torque, 0.375\ x 0.188\ Keyway

  • For use with Lovejoy 1000 series grid coupling assembly (sold separately).
  • Open-style shaft hub for horizontal- or vertical-style grid coupling assemblies.
  • Stamped steel for strength and durability.
  • Supports constant angular misalignment of up to 0.25 degrees.
  • Imperial unit measurements for industry consistency.
Check Stock

uxcell 10mm to 10mm Bore Rigid Coupling Set Screw L22XD16 45# Steel,Shaft Coupler Connector,Motor Accessories

  • Connection Diameter: 10mm to 10mm, Total Length: 22mm /0.87 inch, Outside Diameter : 16mm/ 0.63 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

uxcell 8mm to 8mm Bore Rigid Coupling Set Screw L22XD14 45# steel,Shaft Coupler Connector,Motor Accessories

  • Connection Diameter: 8mm to 8mm, Total Length: 22mm /0.87 inch, Outside Diameter : 14mm/ 0.55 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

uxcell 7mm to 7mm Bore Rigid Coupling Set Screw L22XD14 Copper,Shaft Coupler Connector,Motor Accessories

  • Total Length: 22mm/0.87 inch, Outside Diameter : 14mm/0.55 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

uxcell 4mm to 4mm Bore Rigid Coupling Set Screw L26XD10 Aluminum Alloy,Shaft Coupler Connector,Motor Accessories

  • Connection Diameter: 4mm to 4mm, Total Length: 26mm /1.02 inch, Outside Diameter : 10mm/ 0.39 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

uxcell 5mm to 6mm Bore Rigid Coupling Set Screw L22XD14 Copper,Shaft Coupler Connector,Motor Accessories,2pcs

  • Connection Diameter: 5mm to 6mm, Total Length: 22mm /0.87 inch, Outside Diameter : 14mm/ 0.55 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

uxcell 1/8 inch to 5mm Bore Rigid Coupling Set Screw L26XD10 Aluminum Alloy,Shaft Coupler Connector,Motor Accessories

  • Connection Diameter: 1/8 inch to 5mm, Total Length: 26mm /1.02 inch, Outside Diameter : 10mm/ 0.39 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

uxcell 5mm to 5mm Bore Rigid Coupling Set Screw L25XD14 Aluminum Alloy,Shaft Coupler Connector,Motor Accessories,Blue

  • Connection Diameter: 5mm to 5mm, Total Length: 25mm /0.98 inch, Outside Diameter : 14mm/ 0.55 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

uxcell 6mm to 10mm Bore Rigid Coupling Set Screw L22XD16 Stainless Steel,Shaft Coupler Connector,Motor Accessories,2pcs

  • Connection Diameter: 6mm to 10mm, Total Length: 22mm /0.87 inch, Outside Diameter : 16mm/ 0.63 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

uxcell 10mm to 10mm Bore Rigid Coupling Set Screw L22XD16 Stainless Steel,Shaft Coupler Connector,Motor Accessories,2pcs

  • Connection Diameter: 10mm to 10mm, Total Length: 22mm /0.87 inch, Outside Diameter : 16mm/ 0.63 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock