Reviews Copper Based Board Pcb

4X Prototype PCB for Arduino Mega 2560 R3 Shield Board DIY

  • Prototype PCB for Arduino Mega 2560 R3 Shield Board DIY..
  • PCB Dimension: 101.6mm x 53.34mm / 4" x 2.1".
  • PCB Thickness: 1.6mm / 0.063", Material: high quality FR-4 glass fiber PCB..
  • All holes are plated through. Top and bottom side are identical copper layers. Pads grid (pitch) 2.54mm / 0.1", hole diameter 0.9mm..
Check Stock

Liftmaster K001A6837 Logic 4 Board Commercial OEM Genuine

  • 【Dimension】 -Size：200mmx150mm/7.87"x5.91"(L*W).
  • 【Material】 -The copper clad laminate is made of FR-4 glass fiber and copper, the number of layers issingle-sided.
  • 【Features】- The copper clad board is resistant to high temperature, is not easily oxidized, is not easily deformed, and is convenient for welding.
  • 【Application】 - PCB circuit boards are very suitable for making PCB circuit boards and models. It is widely used in product development, DIY experiment, maintenance, production, etc.
  • 【Noted】 -The product may be slightly scratched or dirty during transportation, which will not affect its use.
Check Stock

zgs78hh 18V Battery Chip Protect Board Replacement Battery Protection, Circuit Board for Makita BL1830 BL1850

  • 【Dimension】 -Size：200mmx150mm/7.87"x5.91"(L*W).
  • 【Material】 -The copper clad laminate is made of FR-4 glass fiber and copper, the number of layers issingle-sided.
  • 【Features】- The copper clad board is resistant to high temperature, is not easily oxidized, is not easily deformed, and is convenient for welding.
  • 【Application】 - PCB circuit boards are very suitable for making PCB circuit boards and models. It is widely used in product development, DIY experiment, maintenance, production, etc.
  • 【Noted】 -The product may be slightly scratched or dirty during transportation, which will not affect its use.
Check Stock

Keyboard Switch Sound Dampeners Sheet Silencer Foam Silencer Pad for Mechanical Keyboard（96 Layout）

  • 【Product Function】 Using this product can eliminate the cavity sound of the keyboard, increase the thickness of the tone, and reduce the resonance....
  • 【Easy Installation 】Install directly between PCB and steel plate without adhesive. And will not affect the light position of the keyboard..
  • 【Material】Made of soft sponge material, with high-efficiency noise reduction effect, and will not damage your PCB board..
  • 【3mm Thickness】Because the distance between the PCB and the positioning board is between 3mm and 3.5mm, this 3mm silencer pad is the best choice....
  • 【Warm Tips】This silencer pad is drawn based on the actual measurement of the keyboard. It is not manufactured by the original factory and cannot....
Check Stock

DNYSYSJ 1500W CNC Router Engraver Machine, 6040 3Axis USB Engraving Drilling Milling Carving Machine 3D Carving Desktop Machine DIY Artwork Woodworking

  • ★【It can work with various materials(metallic & non-metallic)】Such as: wood, pmma or other plastic, MDF board, native wood, PVC, Acrylic, wood, composite board plywood. and soft metal .like aluminum, copper and silver to engrave them into 3D/2D works etc. The machine can connect with computer as other external device such as printer, scanner. With the assist of the ROUTER 6040T, your design idea will be real-time display..
  • ★【Water cooled spindle motor】It can work longer time than air cooled motor.Water cooled spindle motor has higher stability and better concentricity than air cooled motor,water cooling spindle works more stable and durable.(tips：1. The spindle motor must connect with the VFD.)The mini router Frame is movable..
  • ★【It can used for engraving】Advertising signs, PCB, nameplates, badges, seals, bronzing plate, aluminum alloy, acrylic plates, ABS resin doublecolor plate, PVC foaming board, indentation plates, signs, construction models, instrument panels, wooden products, etc..
  • ★【Wide Range of Applications】This 6040 machine is suitable for industry, Technology Research, Advertising Design, Arts Creation, Teaching, Student Project and Hobby Purposes. Suitable for PCB, wood, Plexi glass, PVC, Crystal Acrylic, RESIN, Pla....
Check Stock

Switch Sound Dampeners Sheet Soft Landing Pads Dimple Foam Sponge (87 Layout)

  • 【Switch Sound Dampeners Sheet】This product is a Switch Sound Dampeners sheet, which is placed between the keyboard's circuit board (PCB) and the positioning board. It is a must for keyboard lovers to DIY your keyboard..
  • 【3mm Thickness】Most of the silencer pads are designed based on a standard 1.5mm positioning plate. Due to the processing accuracy of the plate, the space between the PCB and the positioning plate ranges from 3mm to 3.5mm. Regardless of whether the keyboard switch is welded or hot-plugged, the 3mm silencer pad is the best choice..
  • 【Warm Tips】This silencer pad is measured and drawn according to the keyboard entity. It is not produced by the original manufacturer and cannot be guaranteed to be fully fitted. Some of the holes, gaps, and circles may be caused by too many models and brands of the same configuration and different designs. The hole is deviated. Please check carefully before placing an order..
Check Stock

Ultra-Small RPi GPIO Terminal Block Breakout Board Module, for Raspberry Pi

  • The item has been soldered and assembled. Support for Raspberry Pi 1 Model B+, Pi 2 Model B, Pi 3 Model B, Pi 3 Model B+, Pi 4 Model B, Pi Zero, Pi Zero-W..
  • Terminal block pitch 2.54mm/0.1", wire size range 28AWG to 18AWG, strip length 4.5mm, screw M1.6 steel, pin header and cage copper..
  • FR-4 fiber glass PCB, dual copper layers..
  • 2x20 positions header connect to Raspberry Pi board..
  • Packing list: 1x terminal block breakout module, 4x M2.5x6mm screws, 4x 10mm nylon standoffs. 2x 11.5mm brass standoffs, 1x small slotted screwdriver (NOTE: the item not include Raspberry Pi Board)..
Check Stock

FDSF USB 3.1 Type C to Type C Extension Cable 90 Degree FPC FPV Ribbon Flat USB C Cable 3A 10Gbps EMI Shielding, 30cm

  • The PCB is made of high-quality materials with high frequency and low resistance. The PCB is made of precision. The PCB uses high TG plates. The thickness of the copper material is thickened to 1oz. The PCB power circuit is strengthened and the use of 2 5V power core wires is strengthened, so that the transmission current is more powerful. Support up to 3A..
  • The differential signal has no via hole design, the signal is pure, there is no signal attenuation interference problem of parasitic capacitance and parasitic inductance, and there is no CAF short circuit phenomenon, and the product is durable..
  • Product application: GPS navigator, storage device, imaging device, for Pi 4 for MCU development board, built-in USB device to extend the use of , convenient for USB power supply and USB signal transmission of SLR handheld pan/tilt, etc..
  • Cable length Description: The length of the wire refers to the part of the visible wire. It does not include the PCB and the connector..
Check Stock

YoungRC EC5 Parallel Charging Board 2S-6S Lipo Battery Balance Charge Board Expansion Board for RC Drone Helicopter Battery Charger

  • Function: This EC5 parallel charging board is suitable for connect and charge 1 to 6 batteries in parallel (including the Li-Po, Li-Fe and Lion) .It can charge 2s-6s battery pack..
  • High quality material: It's made of Pcb + Plastic. Using high-quality multi-strand silicone wire，Thicker PCB copper. Safe, durable and long service life..
  • High efficiency: It charge and balance up to multiple batteries at the same time instead of balancing batteries one by one, save your time. Stable and ensure efficient work..
  • ★★Note: The EC5 parallel charging board only support charging multiple batteries with the same voltage (2S With 2S, 3S With 3S, Etc) and the same cell count at the same time. Otherwise, the battery and charging board may be damaged, or even cause a fire..
  • If you encounter any problems during use, please do not hesitate to contact us at any time, we will try our best to help you.
Check Stock

Zorveiio 50 Pcs PCB Board Mounting Feet with Screws, PCB Spacer Kit PCB Feet Plastic PCB Standoffs for Arcade Gaming Board Console Motherboard

  • 【Premium Material】Our pcb board mounting feet are made of high quality insulating plastics, which is sturdy, strong enough and durable in use. Such reliable plastic spacer can stay firmly on PCB Board, good insulation with long service life..
  • 【Pacakge & Suitable Size】 You will receive 50pcs L type pcb feet and 100pcs mounting screws (Each foot comes with 2 pieces screws). Each pcb standoff measures approx. 0.8" x 0.8"/21.2mm x 20.3mm, can secure the board tightly. Sufficient enough for you to satisfy using and replacing daily needs..
  • 【Widely Usage】Our plastic pcb feet are suitable for PCB packaging and stacking applications. Specially for fixing gaming boards, game console motherboard, video board, arcade gaming board ect and work well. Serve as ideal replacement hardware parts and offer you much convenience in your daily life..
  • 【Easy to install】 These pcb spacer kit is easy to install and use, you just need to tighten mounting screws in a breeze, will not need a lot of labor. It can secure the circuit board to other surfaces effortlessly..
  • 【100% Risk-Free Shopping】 Zorveiio's products are backed by incredible customer service to make sure your satisfaction is guaranteed. If you have any other questions about it, please do not hesitat....
Check Stock

YUNGUI PCB Protoboard,3 Pack PCB Prototype Board Solderable Breadboard for DIY Electronics and Soldering kit(4” X 6”,Blue)

  • ♔The material is all FR4 full glass fiber plate, all Copper foils are Tin-plating for strength,which can effectively prevent the pad from falling off..
  • ♔The solderable breadboard contains 2 size hole diameter of 1mm/0.04”and 1.4mm/0.055”. PCB protoboard holes are Suitable for resistor,capacitor,AWG(American Wire Gauge),SWG (Stand Wire Gauge),and other Electronic Components..
  • ♔PCB board is more suitable for analog circuits and discrete circuits,four mounting holes at the corners of the board are very convenient for installing them together..
  • ♔Electronic parts and Electronic equipment replaced and Repaired include: LCD Modules, Optoelectronic Displays, Capacitors , Resistors , Potentiometers , LED Displays , Electronic Accessories & Supplies,Electronics Stocks,Ative Compent , Integrated circuit , Diode , Transistor..
  • ♔Our Guarantee:Quality assurance,efficient service.Fast Shipping! We provide 30 day money-back and 12-months warranty. Please feel free to contact us if you have any question..
Check Stock

Dashtop 40 pcs L Type PCB Mounting feet / legs with Screw Fit for Arcade Games Jamma Game Video Games Windows System Raspberry Pi Board

  • MATERIAL: PCB standoffs are made of insulating plastics, strong and durable in use..
  • SIZE: The size of insulated PCB spacer – 20 x 20 x 9mm / 0.8 x 0.8 x 0.35in (LxWxH). Supporting Height: 20mm / 0.8 inch.
  • TWO SCREWS HOLES: Each L type PCB board mounting feet comes with 2 screws to secure the circuit board to other surfaces easily.
  • APPLICATIONS: Circuit Board Standoffs suit for game console motherboard, video board, and so on, serve as ideal replacement parts and provide you much....
  • Apply for: our L type PCB board mounting feet with screws fit well with arcade gaming board, video board and so on, serve as ideal replacement parts....
Check Stock

Yellow Sanwa LB35 Balltop for JLF Joysticks

  • Original Sanwa Denshi TP-MA Replacement PCB with Microswitches.
  • Replacement microswitch PCB for Sanwa JLF series Joysticks.
  • Often the PCB is the first to go out on a Sanwa JLF in a few years. Restore it to brand new by getting the Sawa TP-MA PCB assembly. This replaces the entire set of microswitches and PCB, and housed in very easy to install module..
  • Installation: Remove the Sanwa JLF lever restricted Remove the TP-MA board that comes from the Sanwa JLF lever Place the new board pointing in the same direction as the previous one. Finally place the restrict again.
  • Package include One pcs Original Sanwa TP-MA PCB with Microswitch.
Check Stock