Reviews Conduit Wiring Box

Jonard Tools ROD-3316 Coated Fiberglass Fish Tape Duct Rodder with Accessory Kit 3/16 x 300

  • CONDUIT RUNNING: Lightweight and portable, this rodder unit is perfect for running conduit inside and outside conduit drops as well as home drops from the hand-hole box to a building.
  • VERSATILE USE: Used for light pole wiring, control wiring, or walker ducts and rod can be pulled horizontally or vertically.
  • NON-CONDUCTIVE: Made with a non-conductive fiberglass core with a yellow nylon coating for high visibility and flexibility.
  • HIGH TENSILE STRENGTH: Can withstand loads up to 200 kgf (441 lbf) for quick and easy pulling.
  • LIGHTWEIGHT & COMPACT: 22” X 17” X 7” (55.88 cm x 43.18 cm x 17.78 cm) and weighing 14.33 lb (6.5 kg) for easy transportation.
Check Stock

Westinghouse Lighting 0124000 Sidemount Plus Fan Box 2-1/8 Inch Deep

  • Sidemount Plus Fan Box allows safe, simple installation of fans and fixtures, ideal for remodel applications.
  • Supports ceiling fans and lighting fixtures up to 70 pounds.
  • Includes three 1/2-inch Romex or conduit knockouts, two sets of Romex knockouts, one Romex clamp.
  • 21.5-cubic-inch wiring capacity, electrical box is 2-1/8 inches deep.
  • Includes sidemount bracket, electrical box, Saf-T-Cap, mounting hardware and instructions.
Check Stock

Westinghouse 0152500 Saf-T-Bar for Ceiling Fans

  • Saf-T-Box allows safe, simple installation of fans and fixtures, ideal for new construction and where attic is accessible.
  • Supports ceiling fans up to 70 pounds or lighting fixtures up to 150 pounds.
  • Includes three knockouts for Conduit or Romex, one Romex clamp.
  • 15.5-cubic-inch wiring capacity, electrical box is 1-1/2 inches deep.
  • Includes Saf-T-Cap, mounting hardware and instructions.
Check Stock

Westinghouse Lighting 0107000 Saf-T-Grid for Suspended Ceilings

  • Saf-T-Box allows safe, simple installation of fans and fixtures, ideal for new construction and where attic is accessible.
  • Supports ceiling fans up to 70 pounds or lighting fixtures up to 150 pounds.
  • Includes three knockouts for Conduit or Romex, one Romex clamp.
  • 21.5-cubic-inch wiring capacity, electrical box is 2-1/8 inches deep.
  • Includes Saf-T-Cap, mounting hardware and instructions.
Check Stock

HDView Camera Back Junction Base Box for Any Type of Cameras Universal Use for Dome or Bullet Cameras That Base Diameter is Smaller Than 4.72 Hide Cable Junction Box Drill Hole on The Plate

  • Compatible camera base diameter: 3.82-4.72 inches, works with any type of Dome or Bullet cameras (You need drill holes on the plate!).
  • Junction box size is 4.75" x 4.75" x 1.7", has 4 screw holes for attaching the dome or bullet camera, for Hiding Cable, Video Balun, Camera Cord.
  • Rear/Bottom access to pass cabling through. 2 Side Holes (size: 3/4 inches each) connect to conduit piping for wiring.
  • Box Center Hole size 3/4" (can connect conduit for ceiling mount or wall mount), Plate center hole size 2".
  • Easy Installation. Material: Aluminum & SECC. Weatherproof Junction box..
Check Stock

Carlon CFB-12 Ceiling Fan Box Saddle Round New/Old Work 4-Inch Diameter by 2-3/8-Inch Depth Black

  • Sidemount Plus Fan Box allows safe, simple installation of fans and fixtures, ideal for remodel applications.
  • Supports ceiling fans and lighting fixtures up to 70 pounds.
  • Includes three 1/2-inch Romex or conduit knockouts, two sets of Romex knockouts, one Romex clamp.
  • 21.5-cubic-inch wiring capacity, electrical box is 2-1/8 inches deep.
  • Includes sidemount bracket, electrical box, Saf-T-Cap, mounting hardware and instructions.
Check Stock

Signaworks LED 3 Light Steady Andon Tower Light Kit - Parts Only, Assembly Required - 2 Position Switches for On/Off - Stack Light…

  • ... KIT - This Kit has all the Parts for you to Build a Highly Visible, Red/Amber/Green LED Andon Tower Light with three 2 position switches to turn each light Off or On Independently. This is an Economic Solution for Budget Minded Facilities to have Custom Andon Lights Stations, including Direct Wire, Extended Cable, Conduit, etc. These parts can build an Andon Light with Stack Light with a pole attached to a switch box and power cord..
  • CUSTOMIZABLE ANDON PARTS KIT INCLUDES: Bright LED Tower Light 110VAC, 10" Threaded Pole w/ Mounting Nuts, Right Angle Mounting Bracket, Selector Switch Box with Color & Switch Operation Labels, Drilled Holes for Light, Power Cord, Three 2 Position Switches with N.O. contacts, 3 Prong Power Cord, Cable Gland, Butt Splices, Terminal Connectors & Wiring Instructions. DOES NOT INCLUDE (Required): electrical knowledge/aptitude, screwdriver, wire stripper/cutter, wrenches, multimeter, crimper..
  • SUPER BRIGHT, LONG LASTING LED ANDON STACK LIGHT - Using Super Bright LEDs with Long LED Life, the Highly Visible Signal Light provides LED Lighting Over the Full Surface of the Lens Section (Not like other cheap, spotty LEDs or replaceable bulbs). Lenses are replaceable in case of damage and should last for 10+ years in most application....
Check Stock

Signaworks LED 5 Light Steady & Flashing Andon Tower Light Kit - Parts Only, Assembly Required - 3 Position Switches for On/Off Operation - Stack Light…

  • ...- This Kit has all the Parts to Build a Highly Visible, Red/Amber/Green/Blue/White LED Andon Tower Light with five 3 position switches to turn each light On-Off-Flash Independently. This is an Economic Solution for Budget Minded Facilities to have Custom Andon Lights Stations, including Direct Wire, Extended Cable, Conduit, etc. These parts can build an Andon Light with Stack Light with a pole attached to a switch box and power cord..
  • CUSTOMIZABLE ANDON PARTS KIT INCLUDES: Bright LED Tower Light 110VAC, 10" Threaded Pole w/ Mounting Nuts, Right Angle Mounting Bracket, Selector Switch Box with Color & Switch Operation Labels, Drilled Holes for Light, Power Cord, Five 3 Position Switches with N.O. contacts, 3 Prong Power Cord, Cable Gland, Butt Splices, Terminal Connectors & Wiring Instructions. DOES NOT INCLUDE (Required): electrical knowledge/aptitude, screwdriver, wire stripper/cutter, wrenches, multimeter, crimper..
  • SUPER BRIGHT, LONG LASTING LED ANDON STACK LIGHT - Using Super Bright LEDs with Long LED Life, the Highly Visible Signal Light provides LED Lighting Over the Full Surface of the Lens Section (Not like other cheap, spotty LEDs or replaceable bulbs). Lenses are replaceable in case of damage and should last for 10+ years in most applications....
Check Stock

Westinghouse Lighting 0110000 Saf-T-Brace for Ceiling Fans 3 Teeth Twist and Lock,Silver Pack of 1

  • Saf-T-Brace allows safe, secure installation of fans and light fixtures, ideal for new construction or remodel.
  • Supports light fixtures up to 150 pounds on 16-inch centers, fixtures up to 50 pounds on 24-inch centers and fans up to 70 pounds.
  • Dual-mount electrical box has 15.5 cubic inches wiring capacity.
  • 1-1/2 inches deep, 6 knockouts for conduit or Romex.
  • Includes brace, electrical box, Saf-T-Cap, one Romex connector, mounting hardware and instructions.
Check Stock

Signaworks LED 3 Light Steady & Flashing Andon Tower Light Kit - Parts Only, Assembly Required - 3 Position Switches for On/Off Operation - Stack Light…

  • ...This is a Kit of all the Parts for you to Build a Highly Visible, Red/Amber/Green LED Andon Tower Light with three 3 position switches to turn each light On-Off-Flash Independently. This is an Economic Solution for Budget Minded Facilities to have Custom Andon Lights Stations, including Direct Wire, Extended Cable, Conduit, etc. These parts can build an Andon Light with Stack Light with a pole attached to a switch box and power cord..
  • CUSTOMIZABLE ANDON PARTS KIT INCLUDES: Bright LED Tower Light 110VAC, 10" Threaded Pole w/ Mounting Nuts, Right Angle Mounting Bracket, Selector Switch Box with Color & Switch Operation Labels, Drilled Holes for Light, Power Cord, three 3 Position Switches with N.O. contacts, 3 Prong Power Cord, Cable Gland, Butt Splices, Terminal Connectors & Wiring Instructions. DOES NOT INCLUDE (Required): electrical knowledge/aptitude, screwdriver, wire stripper/cutter, wrenches, multimeter, crimper..
  • SUPER BRIGHT, LONG LASTING LED ANDON STACK LIGHT - Using Super Bright LEDs with Long LED Life, the Highly Visible Signal Light provides LED Lighting Over the Full Surface of the Lens Section (Not like other cheap, spotty LEDs or replaceable bulbs). Lenses are replaceable in case of damage and should last for 10+ years in most application....
Check Stock

Signaworks LED 4 Light Steady & Flashing Andon Tower Light Kit - Parts Only Assembly Required - 3 Position Switches for On/Off Operation - Stack Light…

  • ...This Kit has all the Parts for you to Build a Highly Visible, Red/Amber/Green/Blue LED Andon Tower Light with four 3 position switches to turn each light On-Off-Flash Independently. This is an Economic Solution for Budget Minded Facilities to have Custom Andon Lights Stations, including Direct Wire, Extended Cable, Conduit, etc. These parts can build an Andon Light with Stack Light with a pole attached to a switch box and power cord..
  • CUSTOMIZABLE ANDON PARTS KIT INCLUDES: Bright LED Tower Light 110VAC, 10" Threaded Pole w/ Mounting Nuts, Right Angle Mounting Bracket, Selector Switch Box with Color & Switch Operation Labels, Drilled Holes for Light, Power Cord, Four 3 Position Switches with N.O. contacts, 3 Prong Power Cord, Cable Gland, Butt Splices, Terminal Connectors & Wiring Instructions. DOES NOT INCLUDE (Required): electrical knowledge/aptitude, screwdriver, wire stripper/cutter, wrenches, multimeter, crimper..
  • SUPER BRIGHT, LONG LASTING LED ANDON STACK LIGHT - Using Super Bright LEDs with Long LED Life, the Highly Visible Signal Light provides LED Lighting Over the Full Surface of the Lens Section (Not like other cheap, spotty LEDs or replaceable bulbs). Lenses are replaceable in case of damage and should last for 10+ years in most appl....
Check Stock

Vanitek 200 Foot Reach, Spring-Steel Fish Tape Reel, with High Impact Case, for Electric or Communication Wire Puller

  • ...electrical or communication wires. This reel winds up and stores excess tape as wire is pulled. Handle lever Assists on rolling the cable back in. The tape is 1/8'' x 1/16'' x 200’ long with a pulling loop at the end..
  • Perfect for Snaking/Thread or Pulling Cables and Wires through or Behind Ceiling, Walls/Drywall, Conduit, PVC, Pipe, Vent, Duct, Hose, Under Carpet or Insulation and more..
  • Use for your interior and exterior Electrical Site Wiring like, Outlet, Plug, Socket, light fixture, Ceiling Fan, Dimmer, Switch, short runs installing electrical box, Electrical Panel, Subwoofer Box, Switch Box, Junction Box, CPU, Breaker Box, Receptacle box, Transformer, Doorbell, Intercom, Surveillance Camera, DCC, Security systems, Smoke detector, Thermostat, Appliances, Hot Tub, Telephone/Internet Line or Cable TV Coax..
  • Also great for your vehicle’s Wiring like for Alarm, Remote starter, Keyless entry, OnStar, Dash/Rear view Backup camera, Radar detector, Wi-Fi, Bluetooth, Entertainment system, Stereo, Horn, Audio speakers, Radio/cassette/Cd/MP3/DVD player units, USB port, GPS navigation, Fog lights, Headlights, And more for your Home, House, Car, Truck, SUV, Boat, Camper RV, ATV, UTV, Golf Car, and so..
  • A must for any wire and cable installation.
Check Stock

OhLectric OL-43688 Ceiling Fan Blades - Perfect Accessory For Replacing Fan Blade - Not Compatible With All Fans - 52-inch Contractor Plus Series - Set Of 5 - Walnut

  • Saf-T-Brace allows safe, secure installation of fans and light fixtures, ideal for new construction or remodel.
  • Supports light fixtures up to 150 pounds on 16-inch centers, fixtures up to 50 pounds on 24-inch centers and fans up to 70 pounds.
  • Dual-mount electrical box has 15.5 cubic inches wiring capacity.
  • 1-1/2 inches deep, 6 knockouts for conduit or Romex.
  • Includes brace, electrical box, Saf-T-Cap, one Romex connector, mounting hardware and instructions.
Check Stock