Molded Grating, Span 5 ft.
- Price For: Each Surface: Grit-Top Item: Molded Grating Mesh Size: 1-1/2" x 1-1/2" Grating Key: None Bearing Bar Width: 0.25" Bearing Bar Spacing Center-to-Center: 1-1/2" Mesh Pattern: Square Bearing Bar Height: 1" Span: 5 ft. Width: 3 ft. Max. Temp.: 140 Degrees F Depth: 1" Color: Yellow Resin Type: Corvex Country of Origin (subject to change): Multiple.
Check Stock
VCT Rear Axle Bearing Remover Puller Slide Hammer Set Remove Semi-Floating
- EASY TO USE: Slide flat end of puller through center of bearing and flat against backside of bearing, then slide washer down the center of the shaft against front side of bearing and tighten the nut on smaller end of puller, then thread a slide hammer (not included) to the puller and slide hammer back and forth until the bearing comes out.
- The washer captures the bearing firmly to distribute the applied force over the entire bearing and prevent damage.
- Use the VCT Pneumatic SAE Standard Rear Axle Bearing Puller 3-Piece Service Set – Domestic Car Vehicle Bearings Removal Tool Kit to service semi-floating rear axle bearings on your vehicle.
- These tools make the job simple and prevent damage to your bearings when pulling.
- Much easier than claw-type axle bearing pullers that slip off and chew up the old bearings.
- For removal only, not intended for installation.
- FITS YOUR CAR: Standard SAE sizes work for most American domestic makes and models.
- Set includes the following sizes to fit main bearing tube – 1 inch to 1-7/8 inches, 1-5/16 inches to 2-3/8 inches, and 1-3/8 inches to 2-7/8 inches.
- Sizes permanently laser-etched on tool for easy identification.
- Each tool fits a basic slide hammer with a 5/8-inch x 18 thread pitch.
Check StockBarn-Shed-Play S/4 Glider Bearing Arm Brackets - 7 1/2' from Hole to Hole
- Set of 4 glider bracket arm with ball bearings..
- 11 guage steel construction with yellow zinc plating.
- Center hole to center hole: 7-1/2". Overall dimensions: 9-1/4" x 1-1/2"..
- Bearing: 5/16". Offset: 1-1/2". Weight limit is 250 lbs per glider bearing arm. 1000 lbs total..
Check StockTOP YO 5 Cut Yo-Yo Bearing - Stainless - Size C YoYo Replacement Bearing -Single
- This bearing surface has 5 different and is designed to keep your string where you want it..
- The concave surface of this bearing is actually made up of several planes designed to gather the string at the center of the bearing.
- Get high-end play without paying a high-end price..
- These bearings offer a smooth long spin and make the perfect upgrade for any size C bearing yo-yo!.
Check StockFluid Head Tripod COMAN Video Camera Tripod Monopod Aluminium Alloy 70.8 inch for Canon Nikon Sony DSLR Camera
- ★【Professional Fluid Head】Support 360°panorama and +90°/ -70° tilted. 5.7lbs lightweight with max.load 17.6lbs.Extends from 24"-70". Standard....
- ★【Quick Installation System】Pressing installation mode makes camera fixed in 1 second.The locking knob is designed to the left side of the ball....
- ★【Center Column and Bearing Plat Adjust】The center column and bearing plat can be horizontally tilted 25 degrees,so no need to adjust legs if....
- ★【Monopod Function & Macro Shooting】 Separable foot tube design allows the separated foot tube to be combined with the center shaft into a....
- ★【Easy Set Up】Flip knob makes the operation more convenient and quick,Only 22” length when 180° reverse folded, 5.7lbs weight suitable for....
Check StockRakstore BFB0712HF 65mm Graphics Card Cooling Fan Replacement for NVIDIA GTX 970 980 980Ti 1060 1070 1070Ti 1080 1080Ti Quiet Cooler Fan
- Fan Dimension: approx. 95mm x 95mm x 15mm.
- Holes distance: approx. 40mm x 40mm x 40mm (Center to Center).
Check StockWFLNHB Live Center 2MT 60 Degree Lathe Medium Duty Live Tailstock Center for Wood & Metal Lathe CNC Work
- Specification: #2 Morse Taper (2MT) shank, 60-degree point, 5000 Max RPM, 600 lbs max workpiece weight, runout of 0.0004in/0.01mm T.I.R..
- Material: The live revolving center is made of precision ground hardened steel, hardened to 61-65HRC, with high rigidity and wears resistance.
- Triple Bearing Design: The 2MT activity center adopts a combination of a thrust ball bearing and two ball bearings for stable and smooth rotation.
- Seal Ring: There is a seal ring at the front gland to prevent the entry of cutting fluid and dust.
- Application: The live center MT2 is specially designed for lathes under medium-speed and medium-load environments. It can be used for high-speed turning and is suitable for CNC lathes.
Check StockSouthwest Wheel 3,500 lbs Trailer Axle Self Adjusting Electric Brake Kit 5-4.5 Bolt Circle
- Pair of TruRyde 10" x 2 1/4" 5-4.5" bolt circle TruRyde hub and drums with parts (2 5/8" from center of one stud to the center of the next stud).
- Pair of TruRyde 10" x 2 1/4" self adjusting TruRyde electric backing plates.
- Works with Al-Ko, Dexter, Lippert,and Quality Trailer Axles.
- Comes with TruRyde bearings, seals, lug nuts, grease caps, cotter pins, spindle washers, spindle nuts, and brake mounting washers and nuts.
- Built for 84 spindles with a 4 hole brake flange (inner bearing L68149, outer bearing L44649).
Check StockDorman 934-620 Drive Shaft Center Support Bearing Compatible with Select Cadillac Models
- Direct replacement - this drive shaft center bearing is designed to match the fit and function of the original bearing on specified vehicles.
- Restores functionality - this bearing is made to fit and fully restore part functionality after the original bearing fails.
- Durable construction - this part is made from quality materials to ensure reliable performance and long service life.
- Trustworthy quality - backed by team of product experts in the United States and more than a century of automotive experience.
- Ensure fit - to make sure this part fits your exact vehicle, input your make, model and trim level into the garage tool.
Check StockDorman 934-626 Drive Shaft Center Support Bearing Compatible with Select Chevrolet / GMC Models
- Direct replacement - this drive shaft center bearing is designed to match the fit and function of the original bearing on specified vehicles.
- Restores functionality - this bearing is made to fit and fully restore part functionality after the original bearing fails.
- Durable construction - this part is made from quality materials to ensure reliable performance and long service life.
- Trustworthy quality - backed by team of product experts in the United States and more than a century of automotive experience.
- Ensure fit - to make sure this part fits your exact vehicle, input your make, model and trim level into the garage tool.
Check StockCCVA 2PCS PLD10010B12HH DC12V 0.40A 4PIN for MSI GTX1080Ti 1080 1070 1060 RX470 480 570 580GAMING Graphics Card Cooler Fans PLD10010S
- Fan Dimension: approx. 95mm x 95mm x 15mm.
- Holes distance: approx. 40mm x 40mm x 40mm (Center to Center).
Check StockVarious Fields Bearing Snatcher Bearing Tools 608 Disassemble Tool 8mm Bore Bearing
- Material: made of metal, not easy to damage, very durable.
- This is a very convenient tool for disassembling the sliding plate 608 bearing. The bearing can be removed in a few seconds..
- it can be used to disassemble&install the wheels bearings of roller skate. speed skating. drift board......
- How to use: Just slide the tool into the center of the bearing and apply a little pressure on the bearing, you can use the tool to remove and replace....
- There is nothing wrong with choosing us: if you have any questions, please feel free to contact us, we will pay for you at any time, please place an....
Check StockUCT202-010T NTN New Ball Bearing Take Up
- Take-up block with spherical roller bearing insert for use with a Rexnord center pull frame.
- Cast-iron housing and self-aligning steel bearing unit for carrying shafts with radial or radial and thrust loads.
- Relubricatable solid one-piece housing take-up block for maximum strength and rigidity.
- Fixed-type bearing with a single setscrew locking collar for secure attachment to a cylindrical shaft.
- Metal clearance seal for no speed or temperature limitations, and no frictional drag.
Check Stock
