Reviews Boring Bar For Parting Operations

Toolly 0XA Wedge Type Quick Change Tool Post Set For Mini Lathe up to 6-9 Inch Swing OXA TOOL POST

  • Quickly and easily install on an engine, bench, or turret lathe for a wide range of operations. Fully interchangeable with Aloris, Dorian, Phase II,....
  • This set includes: No. 0 Wedge Type Tool Post(1.75" L x 1.75" W x 2.5" H), No. 1 Turning & Facing Holder(up to 1/2" tool capacity),.
  • No. 2 Boring Turning & Facing Holder (up to 1/2" tool capacity), No. 4 Heavy Duty Boring Holder (3/8" & 1/2" tool capacity),.
  • No. 7 Universal Parting Blade Holder (1/2" tool capacity), No. 10 Knurling, Turning & Facing Holder (up to 1/2" tool capacity)..
  • Stud size is M10 and is perfect for most mini lathes, although modification may be needed for some machines (a bushing or new center stud for a....
Check Stock

iCarbide 3/4 Shank Indexable Boring Bar 6pcs Set with 6pcs Carbide Inserts

  • Sclcr Boring Bar 1-1/2" Shank Diameter, Overall Length 14”.
  • Insert Material: made of solid carbide with Multilayer coated, offer long tool life and faster cutting speed, low friction coefficient, good wear resistance.
  • OSCARBIDE boring bars Used for Turning internal hole, reaming, copying,etc.,used for semi-finishing on the existing hole cutter,fit boring machine, lathe machine.
  • CCMT120408( CCMT432) Carbide Inserts 80 degree，negative 5 degree end & side cutting angle.
  • For semi-finishing and finishing operations.
Check Stock

Accusize Industrial Tools 1/2 x 1/2 x 4 in. (Width by Height by Oal) Hss+5% M35 Cobalt Lathe Tool Bit, 5095-0032

  • M35 Cobalt (HSS + 5%) square lathe tool bits blank, much harder and more durable than M2 high-speed steel lathe tool bits.
  • Ground for heavy-duty cuts on casting and forgings. It has significantly higher wear resistance than M2 HSS。.
  • You may machine it to turning tools to do any lathe turning operations. The possibilities are infinite..
  • Step turning, taper turning, chamfer turning, contour turning, facing, grooving, parting, cut-off, internal threading, outside threading, boring, knurling, etc..
Check Stock

Accusize Industrial Tools 5/8'' Sclcr Indexable Boring Bar with 1 Ccmt32 Insert, P252-S405

  • Shank Diameter: 5/8''. Overall Length: 8''. Min. Bore: 0.866''..
  • Boring from light roughing to finishing in small bores. Insert CCMT 32.51 Included & Key Included.
  • Accepts Inserts CCMT 32.51 and CCMT 32.52. Profiling bar for semi-finishing and finishing operations.
  • Bar hardness approximately 45HRC. Extreme gloss finish.
  • Negative 5 degree end & side cutting angle. Positive 80 degree diamond CCMT inserts.
Check Stock

Accusize Industrial Tools 1'' x 12'' Oal Right Hand S-Mwln Heavy-Duty Boring Bars with Wnmg43 Insert(Oxide Body), 0028-1970

  • Profiling bar for semi-finishing and finishing operations.
  • Boring from light roughing to finishing in small bores.
  • Using 80 degree carbide WNMG inserts negative 5 degree end and side cutting angle.
Check Stock

Auliuakz Boring Bar Set,9pcs HSS Material 1/2 inches Round Shank Boring Bar Set Machine Tool Accessories

  • Boring Bar Set:Made of high quality HSS material, high hardness, wear resistance and heat resistance..
  • Boring Bar Set:9 kinds of boring bar of different lengths to meet your different needs..
  • Boring Bar Set:Boring bar can be used on boring machine, lathe or milling machine..
  • Boring Bar Set:Excellent workmanship to ensure high accuracy..
  • Boring Bar Set:The handle of boring bar is thicker, more durable..
Check Stock

YG-1 P15202 Spade Drill Straight Shank Holder, Straight Flute, 0.318\ Shank Diameter, 31/32\-1-3/8\ Drill Insert Range

  • ☞This product is the main accessory of coordinate boring machine, horizontal boring machine, ordinary boring and milling machine, boring and milling CNC machine tools. It can be used for boring, boring outer circle, boring end face, boring stepped hole, boring inner hole end face, cutting inner hole and ring groove on outer circle, etc..
  • ☞Precise control and free adjustment: The scale of the dial is clear, and the circle is divided into 100 equal parts. The movement of each scale is 0.005mm, the diameter is 0.01mm, and the operation is simple..
  • ☞Select material with high hardness. Using 40CrMo material, it has strong rigidity, special surface treatment, high hardness, good seismic performance, suitable for high speed, and guarantees the density of hole processing..
  • ☞The boring range of the complete set of boring tools: 10-150mm, and the diameter of the boring tool bar is 50mm. Precision fine-tuning: 0.01mm (one revolution of 0.02mm), adjustable stroke 20mm. The boring bar easily and directly enters the boring head hole..
  • ☞The refined boring bar is made of alloy steel, which has strength and toughness, good hardenability, and no obvious temper brittleness. After quenching and tempering, it has obvious impact resistance. The taper design of the b....
Check Stock

Accusize Industrial Tools 3/4 x 10 Rh Sclcr Indexable Boring Bar with 10 Pcs Ccmt Carbide Cvd Coating Insert P252-S407Ins

  • 1 pc 3/4'' x 10'' RH SCLCR Indexable Boring Bar.
  • With broad capability for steel, stainless steel, grey and nodular cast-iron.
  • Operations: turning, facing and profiling.
Check Stock

VeYocilk Lathe Threading Carbide Inserts:10 Pcs 11IR A60 1/4 Carbide Inserts for Internal Threading Holders CNC Cutting CNC Turning Tool

  • High Efficiency: This turning tool holders kit for semi-finishing and finishing operations, can reduce the tool grinding cost and improve the cutting efficiency..
  • High Performance: Made of carbide and the coating material is TIN, it can be used for processing steel, the inserts has high hardness, low friction coefficient, good wear resistance and strong impact resistance..
  • Threading Boring Bars: The material of the boring bar is 40Cr steel, widely use, tightly impacted bolt, simple structure, often used for small hole machining..
  • Package Includes: 1PC SNR0008K11 + 1PC SNR0010K11 + 1PC SNR0012M11 turning tools + 3PCS 11IR A60 turning inserts + 3PCS T8 wrench..
  • Best Service: The carbide inserts and turning tools holder are packed in plastic containers, which is safe and easy to store. Any more question about this item, please feel free to email us..
Check Stock

Accusize Industrial Tools 1'' by 12'' Rh Sclcr Indexable Boring Bar Plus 10 Pc Ccmt32.5 Carbide Black and Yellow Inserts, Cvd Coating, P252-S408ins

  • Shank Diameter: 1". Overall Length: 12". Using 80 degree carbide CCMT inserts negative 5 degree end and side cutting angle.
  • Boring from light roughing to finishing in small bores. Insert CCMT 32.51 or CCMT32.52 Included & Key Included..
  • Accepts Inserts CCMT 32.51 or CCMT32.52. S16T-SCLCR4. Profiling bar for semi-finishing and finishing operations.
  • Bar hardness approximately 45HRC. Extreme fine gloss finish.
  • Negative 5 degree end & side cutting angle. Positive 80 degree diamond CCMT inserts.
Check Stock

7PCS Carbide Turning Inserts Lathe Threading Tool Set, 12mm Mini Indexable Shank Lathe Drill Bar Turning Tool with Carbide Inserts for Finishing Operations

  • High-Quality Materials: Made of durable high-quality alloy steel materials with hardened and sharp carbide blades for effective processing..
  • Durability and Sharpness: Tungsten carbide blades are tinned to provide long life and sharpness, and have a higher temperature than ordinary steel tools. The turning tool holder is made of high-quality steel and plated with nickel, which has durability, moisture resistance, rust resistance and corrosion resistance..
  • Excellent Cutting Performance: Each tool holder has a cemented carbide insert with a positive cutting angle and a built-in chip breaker, which is very suitable for general cutting operations..
  • Usage Scenarios: It is used for turning inner holes, reaming, boring, etc. Used for semi-finishing machining on the basis of existing holes on boring machines or lathes..
  • Product Packaging: Including Shank Lathe Drill Bar Turning Tool model S12M-SCLCR06 / SER1212H16 / SCL1212H06 / MGEHR1212-2 / SNR0012M11 / SDNCN1212H07 / SDJCR1212H07.
Check Stock

MT2 Boring Shank, Mt2-1-1/2-18- (m10) Manganese Steel Boring Bar CNC Lathe Tool Inch Boring Head Shank Connecting Rod

  • HIGH-QUALITY MATERIALS: The boring bar is made of high-quality manganese steel to improve durability and service life..
  • SCOPE OF APPLICATION: Boring bar for CNC lathes with 1/2 "boring head. It can be used for boring, round, end face, step hole, inner hole end face, cutting inner hole and annular groove on the outer circle, etc..
  • ACCURATE THREAD: The thread of the boring bar is accurate and can be tightly connected with the boring head..
  • EXQUISITE WORKMANSHIP: The connecting rod of the British boring head handle is very smooth, professional and practical appearance design, easy to use..
  • HIGH STABILITY: MT2 bracket is stable, accurate and high stability, very stable during work, and reliable tools..
Check Stock

Industrial Service Solutions Aftermarket Gardner Denver Aeon 4000 (1 Gal.) Compressor Oil | 1 Gallon | Replacement Lubricant | for Compressed Air Equipment and Systems

  • Mobil met 766 is used for tapping, threading, milling, gear shaving and shaping, broaching, planning, parting-off and automatic lathe operations.
  • Increased production resulting from longer tool life and reduced downtime for tool changes.
  • Improved surface finish, closer tolerances and reduced formation of built-up edge resulting in fewer rejects.
  • Cooler work pieces and increased feed rates possible for reduced operating costs.
  • Suitability for a wide range of severe machining operations on difficult steels.
Check Stock