Reviews Bevel Gear Load Capacity

2Pcs Tapered Bevel Pinion Gear Bevel Gears 12mm Hole 1.5 Module 16 Teeth for Hardware Mechanical Rotation

  • ✅【Widely Usage】Widely use in conveying, agricultural equipment, textile machinery, printing machinery, automotive applications, etc.Suitable for all kinds of mechanical transmission occasions..
  • ✅【16 Teeth Tapered Bevel Pinion Gear 】This mechanical bevel gears only can fits for 1.5 module gear,16 teeth,90 degrees,12mm Hole Diameter..
  • ✅【Easy to Use】The bevel gear set comes with two M5 screws for simplicity and convenience to use.Lower contact ratio between gears, higher load capacity..
  • ✅【Robust and Durable】The Bevel Gears Wheel are made of 45# steel with high wear-resistance,strong and durable..
  • ✅【Note】Please note that this 1:1 bevel gear wheel can only used with 1:1 gear wheel, and can not match the other modulus of teeth..
Check Stock

Yibuy 2 PCS 45# Steel 16 Teeth 1.5 Module 8mm Hole Diameter Bevel Gear Wheel

  • 64 teeth for use with G486Y-P mating bevel gear in 4:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

T159348 Axle Bevel Gear Aftermarket for John Deere Backhoe Sub. No. 4461351022

  • 16 teeth for use with L149Y-G mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

Boston Gear G485Y-G Bevel Gear, 2:1 Ratio, 0.250\ Bore, 24 Pitch, 36 Teeth, 20 Degree Pressure Angle, Straight Bevel, Keyway, Brass

  • 36 teeth for use with G485Y-P mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

EXAUTOPONE Stainless Steel Bevel Gear Set AR44 Compatible with AR44 Heavy Duty RC Car Bevel Gear Set 30T/8T

  • 32 teeth for use with L149Y-P mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

1PC 90-Degree reversing Angle Gear Right Angle Gear Steering Small Bevel Gear Box Bevel Gear Speed Ratio 1:1 (A)

  • 16 teeth for use with PA4416Y-G mating bevel gear in 4:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

Boston Gear L153Y-G Bevel Gear, 1.5:1 Ratio, 0.750\ Bore, 10 Pitch, 30 Teeth, 20 Degree Pressure Angle, Straight Bevel, Steel

  • 30 teeth for use with L153Y-P mating bevel gear in 1.5:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

Boston Gear L147Y-P Bevel Pinion Gear, 2:1 Ratio, 0.188\ Bore, 20 Pitch, 10 Teeth, 20 Degree Pressure Angle, Straight Bevel, Steel

  • 10 teeth for use with L147Y-G mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

PGFUN 2 Pcs 1M 20 Teeth 5/6/8mm Shaft Hole Tapered Bevel Gear 1:1# 45 Steel 1 Module 90 Degree Steering Gear with M5 Fixing Hole (5 mm)

  • 18 teeth for use with L152BY-G mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

Boston Gear HL148Y-P Bevel Pinion Gear, 2:1 Ratio, 0.375\ Bore, 16 Pitch, 12 Teeth, 20 Degree Pressure Angle, Straight Bevel, Keyway, Steel with Case-Hardened Teeth

  • 12 teeth for use with HL148Y-G mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Case-hardened teeth for applications where hardness and strength are needed to transmit torque and motion.
Check Stock

CNBTR 2PCS 45# Steel 2 Modulus 20 Teeth 14mm Hole Dia 90 Degrees Tapered Bevel Gear Wheel

  • Made of high quality 45# steel ,high wear-resistance,longtime use..
  • Lower contact ratio between gears, higher load capacity..
  • It only can fit for 2module gear,20 teeth,90 degrees,Hole Dia 14mm..
  • Suitable for used in agricultural equipment, textile machinery, printing machinery, Mechanical transmission, etc..
  • Note:1 to 1 bevel gear (only 1 to 1 match, can not match with other modules and other number of teeth).
Check Stock

CNBTR Tapered Bevel Pinion Gear 12mm Hole Diameter 45# Steel 1.5 Module 16 Teeth Pack of 2

  • Made of 45# steel with high wear-resistance,strong and durable..
  • Lower contact ratio between gears, higher load capacity..
  • It only can fit for 1.5 module gear,16 teeth,90 degrees,12mm Hole Diameter..
  • Suitable for used in agricultural equipment, textile machinery, printing machinery, Mechanical transmission, etc..
  • Note:1 to 1 bevel gear (only 1 to 1 match, can not match with other modules and other number of teeth).
Check Stock

Bang II (Feat. Uppercase 5ive)

  • Fully milled gearbox housing made of 6061-T6 aluminum for the rear axle of ATOPRC.
  • Due to its dimensional stability results in a higher load capacity and service life of bevel gear and ball bearings. The problem of the torn fastening thread has an end with this case.
  • The bearing adapters are included in the set.
  • We recommend gluing the bearings with threadlocker y0113. For mounting the bearing adapters in the housing we recommend Bindulin silicone y19015. To use HD differential shafts y1477, the Atoprc bearing adapters must be machined.
Check Stock