Reviews Bevel Gear Angle

Boston Gear L149Y-G Bevel Gear, 2:1 Ratio, 0.500\ Bore, 16 Pitch, 32 Teeth, 20 Degree Pressure Angle, Straight Bevel, Steel

  • Multi Sizes Bevel Gears to Choose from: 1M, 1.5M, 2M/ 5mm, 6mm, 8mm shaft hole, the key specs for this gear- 1:1 ratio,1 module, 20 teeth, 5mm shaft hole, M5 fixing hole, 90 degrees steering angle..
  • Widely applied in agricultural equipment, textile machinery, printing machinery, mechanical transmission, automotive and other industries that needs steering drive..
  • The bevel gear is made of 45# steel features high wear-resistance, strong and durable..
  • Note: 1 bevel gear only match 1 same scale gear, so 1 set （2 or more gears) should be replaced together for smoothly drive..
Check Stock

PGFUN 2 Pcs 1.5M 20 Teeth 8/10/12/14/15/16mm Shaft Hole Tapered Bevel Gear 1: 1# 45 Steel 1.5 Module 90 Degree Steering Gear with M5 Fixing Hole (10mm)

  • Multi Sizes Bevel Gears to Choose from: 1M, 1.5M, 2M/ 5-16mm shaft hole, the key specs for this gear- 1:1 ratio,1.5 Module, 20 teeth, 10mm shaft hole, M5 fixing hole, 90 degrees steering angle..
  • Widely applied in agricultural equipment, textile machinery, printing machinery, mechanical transmission, automotive and other industries that needs steering drive..
  • The bevel gear is made of 45# steel features high wear-resistance, strong and durable..
  • Note: 1 bevel gear only match 1 same scale gear, so 1 set （2 or more gears) should be replaced together for smoothly drive..
Check Stock

Yibuy 2 PCS 45# Steel 16 Teeth 1.5 Module 8mm Hole Diameter Bevel Gear Wheel

  • 64 teeth for use with G486Y-P mating bevel gear in 4:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

T159348 Axle Bevel Gear Aftermarket for John Deere Backhoe Sub. No. 4461351022

  • 16 teeth for use with L149Y-G mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

Boston Gear G486Y-G Bevel Gear, 4:1 Ratio, 0.313\ Bore, 32 Pitch, 64 Teeth, 20 Degree Pressure Angle, Straight Bevel, Keyway, Brass

  • ★[OPTIMAL PERFORMANCE]: EXAUTOPONE premium Stainless Steel Bevel Gear Set made of premium stainless steel material improves gear mesh, and with delicate workmanship, which is durable and hard, and long service life..
  • ★[GREAT APPLICATION]:EXAUTOPONE premium Stainless Steel Bevel Gear Set provides over drive for the front axle, helping to pull car climb easily. And it can guarantee to meet the original equipment..
  • ★[FITMENT]:Compatible with AR44 axles, including a 8T bevel gear and a 30T bevel gear..
  • ★[HIGH QUALITY]:EXAUTOPONE premium Stainless Steel Bevel Gear Set is 100% brand new aftermarket unit built to meet OEM specifications. easy to install and remove, ideal replacement for the old or broken one. Factory price with higher cost-effective..
  • ★[PACKAGE & WARRANTY]:Package Includes 1 Pcs X 30T/8T Stainless Steel Bevel Gear Set . Any question just contact us, we will reply you within 24H.And we offer a 12 month warranty..
Check Stock

Boston Gear G485Y-G Bevel Gear, 2:1 Ratio, 0.250\ Bore, 24 Pitch, 36 Teeth, 20 Degree Pressure Angle, Straight Bevel, Keyway, Brass

  • 36 teeth for use with G485Y-P mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

EXAUTOPONE Stainless Steel Bevel Gear Set AR44 Compatible with AR44 Heavy Duty RC Car Bevel Gear Set 30T/8T

  • 32 teeth for use with L149Y-P mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

1PC 90-Degree reversing Angle Gear Right Angle Gear Steering Small Bevel Gear Box Bevel Gear Speed Ratio 1:1 (A)

  • 16 teeth for use with PA4416Y-G mating bevel gear in 4:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

Boston Gear L153Y-G Bevel Gear, 1.5:1 Ratio, 0.750\ Bore, 10 Pitch, 30 Teeth, 20 Degree Pressure Angle, Straight Bevel, Steel

  • 30 teeth for use with L153Y-P mating bevel gear in 1.5:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

Boston Gear L147Y-P Bevel Pinion Gear, 2:1 Ratio, 0.188\ Bore, 20 Pitch, 10 Teeth, 20 Degree Pressure Angle, Straight Bevel, Steel

  • 10 teeth for use with L147Y-G mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

2Pcs Tapered Bevel Pinion Gear Bevel Gears 14mm Hole 2 Module 20 Teeth for Hardware Mechanical Rotation

  • ✅【Widely Usage】Widely use in conveying, agricultural equipment, textile machinery, printing machinery, automotive applications, etc.Suitable for all kinds of mechanical transmission occasions..
  • ✅【Robust and Durable】The Bevel Gears Wheel are made of 45# steel with high wear-resistance,strong and durable..
  • ✅【Easy to Use】The bevel gear set comes with two M5 screws and 1 spanner for simplicity and convenient use.Lower contact ratio between gears, higher load capacity..
  • ✅【20 Teeth Tapered Bevel Pinion Gear 】This mechanical bevel gears only can fits for 2 module gear,20 teeth,90 degrees,14mm Hole Diameter..
  • ✅【Warm Note】Please note that this 1:1 bevel gear wheel can only used with 1:1 gear wheel, and can not match the other modulus of teeth..
Check Stock

2Pcs Tapered Bevel Pinion Gear Bevel Gears 12mm Hole 1.5 Module 16 Teeth for Hardware Mechanical Rotation

  • ✅【Widely Usage】Widely use in conveying, agricultural equipment, textile machinery, printing machinery, automotive applications, etc.Suitable for all kinds of mechanical transmission occasions..
  • ✅【16 Teeth Tapered Bevel Pinion Gear 】This mechanical bevel gears only can fits for 1.5 module gear,16 teeth,90 degrees,12mm Hole Diameter..
  • ✅【Easy to Use】The bevel gear set comes with two M5 screws for simplicity and convenience to use.Lower contact ratio between gears, higher load capacity..
  • ✅【Robust and Durable】The Bevel Gears Wheel are made of 45# steel with high wear-resistance,strong and durable..
  • ✅【Note】Please note that this 1:1 bevel gear wheel can only used with 1:1 gear wheel, and can not match the other modulus of teeth..
Check Stock

PGFUN 2 Pcs 1M 20 Teeth 5/6/8mm Shaft Hole Tapered Bevel Gear 1:1# 45 Steel 1 Module 90 Degree Steering Gear with M5 Fixing Hole (5 mm)

  • 18 teeth for use with L152BY-G mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock