Reviews Bearing Removal Tool Set

VCT Rear Axle Bearing Remover Puller Slide Hammer Set Remove Semi-Floating

  • EASY TO USE: Slide flat end of puller through center of bearing and flat against backside of bearing, then slide washer down the center of the shaft against front side of bearing and tighten the nut on smaller end of puller, then thread a slide hammer (not included) to the puller and slide hammer back and forth until the bearing comes out.
  • The washer captures the bearing firmly to distribute the applied force over the entire bearing and prevent damage.
  • Use the VCT Pneumatic SAE Standard Rear Axle Bearing Puller 3-Piece Service Set – Domestic Car Vehicle Bearings Removal Tool Kit to service semi-floating rear axle bearings on your vehicle.
  • These tools make the job simple and prevent damage to your bearings when pulling.
  • Much easier than claw-type axle bearing pullers that slip off and chew up the old bearings.
  • For removal only, not intended for installation.
  • FITS YOUR CAR: Standard SAE sizes work for most American domestic makes and models.
  • Set includes the following sizes to fit main bearing tube – 1 inch to 1-7/8 inches, 1-5/16 inches to 2-3/8 inches, and 1-3/8 inches to 2-7/8 inches.
  • Sizes permanently laser-etched on tool for easy identification.
  • Each tool fits a basic slide hammer with a 5/8-inch x 18 thread pitch.
Check Stock

Lidscura 8PCS Motorcycle Bearing Pullers 9-23mm Motorcycle Internal Bearing Removal Tool Kit Inner Bearing Extractor Kit

  • Widely Application: This Remover tool kit is ideal for internal bearing removal of automotive flywheel, motorcycle wheel, bicycle wheel, pump bearing generator bearing, machine bearing etc..
  • Meet Your Different Needs: Internal bearing Extractor tool set is equipped with 5 different sizes of open clips. The bearing can be disassembled from 0.35inch(9mm) to 0.91 inch(23mm) inside diameter..
  • Fine Workmanship: This motorcycle bearing pullers set is made of high-quality chrome vanadium steel, strong and durable for for a long service time..
  • Easy to Use: Connect this bearing puller kit with 1/2" 3/4" male thread water faucet, open clamps by turning handle clockwise to snug against the bearing for taking out the inner bearing..
  • Instructions for use: First the tool head into the inner ring of the bearing, and then screwed into the shaft, the tool head propped open hooked bearing inner ring, and then turn the shaft, you can pull out the bearing.
Check Stock

DASBET 16PCS Blind Inner Bearing Puller Hole Remover Extractor Set Slide Hammer Tool Kit

  • 【Applicable】This inner bearing puller set is designed for loosening and pulling tight bearings and bushings, and fit for all vehicles 8-53MM bore bearing..
  • 【Instructions to operate】: How to use? Firstly insert the correct collet in the bore of the bearing and turn the nut to expand the collet till it is secure within the bearing.
  • Attach the small slide hammer and yank the weight towards the handle to give an extra snap of weight.
  • Repeat action until the bearing or bushing has been removed.
  • U-shaped bearing seal puller can be used by threading the bushing puller onto the collet and tightening the nut to slowly pull the bearing out of place..
  • 【Usage】This slide bearing removal tool is designed to quickly finish the job without damaging the removed parts or the tool. This small bearing puller tool is ideal for professionals and do-it-yourselfers..
  • 【Sturdy Construction】: Constructed of a strong, durable carbon steel, the bearing extractor tool is sure to pull even the toughest wheel bearing and bushings from tight positions. This blind bearing puller set has a long steel rod and a T-bar handle. The flared ends of the shop hammer weight provides a sturdy grip. The forged hardened steel and rust-proof finish help to increase pulling strength an....
Check Stock

Orion Motor Tech 3\ 4\ 6\ 3-Jaw Gear Puller Set for Removal of Bearings Pulleys Flywheels (GD)

  • Universal Removal Tool: This 3-jaw removal tool set works with your wrench, ratchet, or spanner as a gear puller, sprocket puller, bearing puller, pulley puller, flywheel puller and more, removing even rusted parts easily and—thanks to its even distribution of force—without damage..
  • Better Together: This professional or home tool kit includes three puller sizes to cover most applications: a 3 inch gear puller with a 2.3" reach and 3" max. spread.
  • a 4 inch gear puller with a 3" reach and 4" max. spread.
  • and a 6 inch gear puller with a 4.7" reach and 6" max. spread..
  • Versatile Reversible Design: Each of the three 3-jaw gear and bearing pullers can be reversed to pull parts from either the inside or outside as needed..
  • 45# Carbon Steel: All parts are made with premium heat-treated 45# carbon steel for maximum strength. The jaws are galvanized and the central screw coated with black oxide to provide superior corrosion resistance and long service life..
  • Satisfaction Guaranteed: Along with this gear and bearing removal tool kit's durable material and careful engineering, you can rest easy knowing that these gear pullers are backed by Orion Motor Tech's warranty and friendly customer service..
Check Stock

Powerbuilt Pilot Bearing Puller, Remove Bearings and Bushings, Foreign and Domestic Car Repair, Storage Case - 648619

  • Made to be the most reliable tools in the market today.
  • Tool set for removal of the pilot bearing and bushings from the flywheel during clutch replacement.
  • Heavy duty puller with 1 1/2-Inch fingers for an extra deep reach.
  • Kit 8 includes 1-Piece for removal of pilot bearing and bushings from the flywheel during clutch replacement.
Check Stock

Orion Motor Tech 3\ 4\ 6\ 8\ 3-Jaw Gear Puller Set for Removal of Bearings Pulleys Flywheels

  • Universal Removal Tool: This 3-jaw removal tool set works with your wrench, ratchet, or spanner as a gear puller, sprocket puller, bearing puller, pulley puller, flywheel puller and more, removing even rusted parts easily and—thanks to its even distribution of force—without damage..
  • Better Together: This professional or home tool kit includes four puller sizes to cover most applications: a 3 inch gear puller with a 4.3" max. reach and 3" max. spread.
  • a 4 inch gear puller with a 5" max. reach and 4" max. spread.
  • a 6 inch gear puller with a 7.3" max. reach and 6" max. spread.
  • and an 8 inch gear puller with a 9.3" max. reach and 8" max. spread..
  • Versatile Design: Each of the three smaller 3-jaw gear and bearing pullers can be reversed to pull parts from the inside or outside.
  • the 8 in. puller can be used in 4 different positions to deal with both medium and large parts..
  • 45# Carbon Steel: All parts are made with premium heat-treated 45# carbon steel for maximum strength. The jaws are galvanized and the central screw coated with black oxide to provide superior corrosion resistance and long service life..
  • Satisfaction Guaranteed: Along with this gear and bearing removal tool kit's durable material and careful engineering, you can rest easy knowing that th....
Check Stock

ATP Blind Inner Bearing Puller Slide Hammer Set Hole Remover Extractor Set 5PCS

  • Premium Quality: The slide hammer puller set is constructed from drop forged steel with a fully chromed carbon steel slide hammer for maximum strength and longevity that resists rust and corrosion..
  • Specifications of The Bearing Puller Set: Overall length 15''/382mm, bearing extractor collets with internal capacity from 3/8"/10mm to 1-1/4"/32mm, bearing extractor 3/8"/10mm to 1/2"/14mm, 9/16"/15mm to 11/16"/19mm. 5/8"/18mm to 1"/25mm, 1"/25mm to 1-1/4"/32mm..
  • Great Function: Open clamps by turning handle clockwise to snug against the bearing, the blind bearing puller is great for pulling out evenly without damage the parts..
  • Wide Application: This pilot bearing removal tool blind hole bearing puller is ideal for pulling jobs,against the bearing for pulling out evenly without damage the parts, and perfect for professional and DIY use..
  • Storage Case: The slide hammer bearing puller is packed in a heavy-duty storage case with precision-sized compartments for every piece - great for storage and transport while lengthening....
Check Stock

OEMTOOLS 37342 Master Wheel Hub and Bearing Remover and Installer Kit Back and Front Wheel Bearing Puller Kit Back and Front Wheel Hub Puller Easy to Use

  • NO SHOP PRESS NEEDED: The OEMTOOLS 37342 Master Wheel Hub and Bearing Remover and Installer Kit saves time removing even seized-up wheel hub and....
  • FOR PROFESSIONAL AND DIY MECHANICS: This wheel bearing puller/installer is one of the only tools for servicing front and rear wheel hubs and bearing....
  • UNIVERSAL APPLICATION: This wheel bearing removal tool features all the adapters needed to service a number of foreign and domestic vehicles, remove....
  • SLIDE-HAMMER-FREE REMOVAL: This wheel bearing tool and hub press makes it simple to remove and install wheel hub and bearing assemblies as well as....
  • WHEEL HUB PULLER KIT INCLUDES: Hub removal tool, Front wheel bearing adapters, Pusher Washers, Receiver Sleeves, Nut-Bolt, and Heavy Duty Bearing.
Check Stock

Bzsunway Front & Rear Bearing Puller Kit Wheel Hub Puller & Bearing Remover & Installer Kit Wheel Hub Remover & Installer Replace OEM 27213 (21pcs)

  • 【High Performance & Time Saving】  No need for other tools, no further calibration after disassembly and installation, the disassembly and installation of the wheel hub and bearing on the vehicle can be easily, accurately and safely completed, saving you more time and energy.
  • 【Wide Compatibility of Adapters】 Our wheel bearing puller/installer tools are specially equipped with suitable adapters for various models (like Volkswagen, BMW, Mercedes-Benz, etc).
  • 【Superior Quality】 Our wheel bearing removal tool set is made of high quality heavy duty stainless steel , durable and sturdy, and can hold up to the torque required to remove hubs and bearings. Ensure long-term use..
  • 【Must Have Tool Kit】 Use our wheel bearing stamping tools without need for a shop press. Whether it is a professional or DIY mechanic, our wheel bearing puller/installer can help you save more time. Tool Kit Use our wheel bearing stamping tools without need for a shop press, which is a must-have tool set for bearing disassembly.
  • 【Satisfactory Service】 If you are not satisfied with our products.You can request a full refund within 30 days to support a 12 month warranty.Professional and sincere service allows you to purchase without risk !.
Check Stock

OEMTOOLS 27059 Pilot Bearing Puller Attachment, Pilot Bearing and Bushing Removal, Fits 5/8” x 18” or 3/4” x 16” Threaded Rods , Black

  • EASY TO USE: The slide hammer bearing puller can be used in four steps: Insert the pilot bearing puller, turn the attachment housing expanding both jaws against the pilot bearing, attach a slide hammer, and use the slide hammer to remove the bearing.
  • SAVE MONEY: Getting a pilot bearing replaced in an auto shop could cost you up to $650.
  • You can save hundreds of dollars by using this one pilot puller.
  • VARIETY OF USES: Not only can this pilot bearing tool be used as a bearing puller, but it can also be used as a bushing tool on starters and generators.
  • This pilot bearing removal tool will also fit any 5/8” x 18” or 3/4” x 16” threaded rods.
  • DURABLE: Made from steel, this bearing and bushing removal tool can withstand years of regular pilot bearing jobs.
  • This blind hole bearing puller is built to last.
  • DIMENSIONS: This pilot bearing remover is easy to store anywhere at just 10.4" x 3.4" x 1.3". The blind bearing puller is also easy to wield, weighing in at just 13.6 ounces, making it a great pilot tool.
Check Stock

OEM TOOLS 27213 Master Wheel Hub & Bearing Remover & Installer Kit Back & Front Wheel Bearing Puller Kit Back & Front Wheel Hub Puller Easy to Use

  • NO SHOP PRESS NEEDED: Remove the need for a shop press with our wheel hub bearing press tool.
  • Save time removing even seized-up wheel hub and bearing....
  • FOR PRO AND DIY MECHANICS: This wheel bearing puller/installer is one of the only tools for servicing front and rear wheel hubs and bearing on German....
  • TIME-SAVING BEARING TOOL: No need to remove the strut assembly or knuckle to remove/install the hub and bearing.
  • VARIETY OF ADAPTERS: Service your vehicles easily with our rear and front wheel bearing removal kit.
  • This wheel bearing removal tool features all the....
  • DURABLE STEEL CONSTRUCTION: Our rear and front wheel drive bearing adapter kit's steel design holds up to the torque required to remove hubs and....
Check Stock

Powerbuilt Harmonic Balancer Puller and Installer Tool Set, Install and Remove Kit, Cars and Light Trucks, Storage Case - 648637

  • Strong and dependable enough to last a lifetime.
  • Kit services: many automobiles and light trucks.
  • Tool set for removal and installation of harmonic balancers that have threaded holes.
  • Removal pieces: combo yoke, national fine center screw, center point piece and bolt pairs.
  • Installation pieces: national fine center screw, thrust bearing, forcing nut and jaw nut.
  • Adapters included: M12-1.5, M14-1.5, M16-2.0, 7/16-Inch-20, 1/2-Inch-20, 9/16-Inch-18 and 3/416.
  • Kit 12 includes 22-Piece for removal and installation of harmonic balancers with threaded holes.
Check Stock

ABN Wheel Bearing Puller Kit Hub Removal Tool Wheel Bearing Tool - Independent Suspension Roll Ball Bearing FWD RWD AWD

  • [No More Hammer or Shop Press]: The ABN Master Wheel Bearing Removal Tool and Wheel Hub Puller Tool Kit allows you to remove and install wheel hub and....
  • [Fits Your Vehicle]: Universal for front, rear, and all-wheel drive vehicles with independent suspension and pressed roller-ball bearings.
  • [Use on Seized-Up Assemblies]: Self-centering mechanism and thrust bearing design.
  • Use the round plate that corresponds to the diameter of your....
  • [Perfect Sizes]: Universal set includes 21 pieces that have A through U permanently printed labels.
  • Pusher washer disk driver sizes from 2.1 inches....
  • [Contents]: Wheel hub and bearing puller set and installation kit includes a remover tool, adapter shoes, pusher washers, receiver sleeves, nut-bolt,....
Check Stock