Reviews Axle Center Assy

3.5k-3500 Lb Capacity Trailer Idler Axle - 5 on 5 Bolt Pattern - Straight Axle (61/46) (Assembled Idler Axle)

10k-10000 lb capacity Electric Brake axle-DEXTER Compatible.
Axle comes assembled with electric brakes, hubs, bearings, races, oil bath and transparent cap.
Option to add spring and ubolt kits needed to hang your axle.
Axle Size: 74" Hubface-46" Spring Center.

3.27-INCH WIDE BY 2.17-INCH LONG WHEELBARROW BRACKET - Exact dimensions are 3.27 inches from end to end of the mounting tabs, while the mounting holes are 2 1/8 inches apart from center to center.
COMPATIBLE WITH 5/8 INCH WHEELBARROW AXLES - These black wheelbarrow axle brackets are a universal fit for wheelbarrows with axles that are 5/8 inch in diameter. This is one of the most common axle sizes for wheelbarrows.
ONLY COMPATIBLE WITH SINGLE TIRE WHEELBARROWS - Part of the brackets’ design are the indentations on one end of the barrel. These indentations prevent the axle from sliding all the way through the bracket.
COMPLETE SET WHEELBARROW AXLE BRACKET - The 4-pack wheelbarrow axle bracket includes a complete set of the required bolts: length 29.62mm/1.17 inches and nuts. As this is a universal fit kit, the mounting holes may not align exactly with the existing holes on the wheelbarrow.
AFFORDABLE WHEELBARROW SPARE PARTS - Don’t just throw away your wheelbarrow just because of a simple defect. These 2 pairs of wheelbarrow axle brackets will ensure that you’ll always have a spare axle bracket on hand.

Borla 140680 S-Type Cat-Back Exhaust System.
Incl. Front Pipe Assy/Muffler Assy/Tailpipe Assy/Polished 4 in. Single Round Rolled Angle-Cut Tip.

?IMPROVE DURABLILITY?Modified for heightened and widened front and rear drive shafts, which is better than ordinary axles, and the axle is higher. The....
?HIGH QUALITY?The aluminum alloy shell, hardened steel structure gears and drive shaft increase durability, and improve service life..
?INCREASE SPACING?The portal axles create extreme amounts of ground clearance under the center of its axle center, increasing the spacing by about....
?SIMPLE INSTALLATION?Easy to install, perfect fit, make your remote control car cooler and more attractive..

EASY TO USE: Slide flat end of puller through center of bearing and flat against backside of bearing, then slide washer down the center of the shaft against front side of bearing and tighten the nut on smaller end of puller, then thread a slide hammer (not included) to the puller and slide hammer back and forth until the bearing comes out.
The washer captures the bearing firmly to distribute the applied force over the entire bearing and prevent damage.
Use the VCT Pneumatic SAE Standard Rear Axle Bearing Puller 3-Piece Service Set – Domestic Car Vehicle Bearings Removal Tool Kit to service semi-floating rear axle bearings on your vehicle.
These tools make the job simple and prevent damage to your bearings when pulling.
Much easier than claw-type axle bearing pullers that slip off and chew up the old bearings.
For removal only, not intended for installation.
FITS YOUR CAR: Standard SAE sizes work for most American domestic makes and models.
Set includes the following sizes to fit main bearing tube – 1 inch to 1-7/8 inches, 1-5/16 inches to 2-3/8 inches, and 1-3/8 inches to 2-7/8 inches.
Sizes permanently laser-etched on tool for easy identification.
Each tool fits a basic slide hammer with a 5/8-inch x 18 thread pitch.

Ideal for use on the drive axle when paired with the NT555G2 on the non-drive axle.
Sidewall construction has been modified to improve launch.
Large twin center ribs provide a continuous contact patch for dry traction..

Ideal for use on the drive axle when paired with the NT555G2 on the non-drive axle.
Sidewall construction has been modified to improve launch.
Large twin center ribs provide a continuous contact patch for dry traction..

Build your own high-center cart with a set of these 20-Inch spooked wheels heavy-duty construction will handle the roughest terrain ball bearing axle.
Heavy-duty construction will handle the roughest terrain.

Kit contains: 2 ball bearings and 2 double lip seals which are positioned in the center axle carrier.
Honda TRX400EX Rear Axle Bearings and Seals Kit 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 **Does not fit aftermarket carriers that use wider bearings..

Centerlock hubs on tubeless-ready rims. 29mm inner width is perfect for today's trail and enduro mountain tires. These wheels come with Quick Release Skewers and the adapters needed to make them 15 x 100 and 12 x 142 thru axle! If you'd like, we will change the axle adapters out before we ship. Just leave a note at checkout and we will take care of it for you!.
Cassette Body Type: Shimano Dynasys 11 Speed Mountain , Shimano/SRAM 8, 9, 10 Speed Hub/Brake Compatibility: Center-Lock Disc Rim Width (Internal): 29 mm ISO Diameter: 622 / road / 29" Front Axle: 15mm Thru x 100mm , QR x 100mm Rear Axle: 12mm Thru x 142mm , 10x1 Threaded x 135mm Tire Type: Tubeless Ready Clincher Wheel Size: 29" Defined Color: Black 982g Front 1234g Rear.