Reviews Axle Bearing Puller

VCT Rear Axle Bearing Remover Puller Slide Hammer Set Remove Semi-Floating

  • EASY TO USE: Slide flat end of puller through center of bearing and flat against backside of bearing, then slide washer down the center of the shaft against front side of bearing and tighten the nut on smaller end of puller, then thread a slide hammer (not included) to the puller and slide hammer back and forth until the bearing comes out.
  • The washer captures the bearing firmly to distribute the applied force over the entire bearing and prevent damage.
  • Use the VCT Pneumatic SAE Standard Rear Axle Bearing Puller 3-Piece Service Set – Domestic Car Vehicle Bearings Removal Tool Kit to service semi-floating rear axle bearings on your vehicle.
  • These tools make the job simple and prevent damage to your bearings when pulling.
  • Much easier than claw-type axle bearing pullers that slip off and chew up the old bearings.
  • For removal only, not intended for installation.
  • FITS YOUR CAR: Standard SAE sizes work for most American domestic makes and models.
  • Set includes the following sizes to fit main bearing tube – 1 inch to 1-7/8 inches, 1-5/16 inches to 2-3/8 inches, and 1-3/8 inches to 2-7/8 inches.
  • Sizes permanently laser-etched on tool for easy identification.
  • Each tool fits a basic slide hammer with a 5/8-inch x 18 thread pitch.
Check Stock

ABN Inner CV Axle Removal Tool - CV Axle Puller Slide Hammer Set with 5 lb Slide Hammer and CV Joint Puller Adapter

  • [Remove Front Wheel Drive Axles Easily] To replace or repair your CV axle joints easily, use the ABN FWD Axle Puller Slide Hammer Puller Set.
  • The CV joint puller adapter and large slide hammer bearing puller allow you to create added torque to loosen and remove stubborn axle shafts and water pumps.
  • [Fits Your Needs] Chrome-plated 23 x 5/8-inch hammer bar features a 5/8-inch x 18 threaded section to fit your adapters, while the slide hammer CV axle adapter has 48mm (roughly 2-inch) opening and a 2.5-inch depth to fit your needs.
  • [Easy to Use] Attach the inner CV axle puller to your axle slide hammer then position the adapter around the shaft behind the inner boot.
  • Slide the 5 lb hammer weight back and forth to create torque to pull out the axle.
  • Use lubricant fluid for added ease (not included).
  • [Safe for Your Vehicle] Slide hammer CV joint puller and attachment design focuses the added torque to the back of the housing to prevent damage to the roller bearing inside the joint.
  • Pulls CV joints on 1986-current Taurus/Sable.
  • [Built to Last] Hardened hammer shaft provides strength and d....
Check Stock

Orion Motor Tech Rear Axle Bearing Puller Tool Kit and Slide Hammer Set | Axle Seal and Bearing Remover Set with Slide Hammer Yoke and 3 Rear Axle Puller Adapters, 1\ to 2-7/8\ IDs

  • 8PC. SLIDE HAMMER SET: This 8-piece professional axle, bearing, and seal removal tool set by Orion Motor Tech provides a 5/8" slide hammer, yoke, locknut, hook, and adapters to let you quickly, easily, and safely repair rear axle problems on the vast majority of domestic cars and light trucks.
  • AXLE PULLER SET: Lock the slide hammer onto the 4-point yoke to set up a flange type axle puller that will let you extract parts with threaded holes, including stud axles, spur gears, and more.
  • SEAL PULLER SET: The 5.5 pound slide hammer and its sturdy T handle provide the firm grip and torque needed to pop out worn and damaged seals and other press fit parts using the included hook.
  • BEARING PULLER SET: The small, medium, and large bearing puller adapters cover inner diameters from 1 to 1-7/8.
Check Stock

10lb Heavy Duty Inner CV Axle Removal Tool for FWD Vehicles Front Wheel Drive Axle Half Shaft Removal Tool,CATUDIY Inner CV Joint Puller Tool & Slide Hammer Puller Set with 48&63MM Joint Fork Adapters

  • Useful CV Axle Puller: To replace or repair the CV axle joints easily, use this slide hammer kit. The CV joint puller adapter and large slide hammer bearing puller allow to create added torque to loosen and remove stubborn axle shafts and water pumps, without damaging to transmission cases or other components.
  • Efficient Front Wheel Drive Axle Puller Set: Efficient & Heavy-Duty: Our 10.5 lb curved slide hammers are heavier and larger, and the length of 19.5 inches ensures sufficient length slide to generate more force(so the generated pulling force is also twice than normal 5lb slide hammer). Save efforts and works more efficiently.
  • Combination Kit Fits All Needs: The CV axle joint pulley removal tool includes a T-style slide hammers, a steel wire joint puller, 2pc 16mm nuts, opening 63mm and 48mm CV joint fork removing attachments. All you need to remove CV axle or half shaft are put in this easy-carrying plastic case.
  • Superior Material: Heat-treated FWD axle puller adapter with black oxide finish is durable and resists rust and corrosion. Slide hammer and the VC join fork is made of high quality heavy steel materials w....
Check Stock

ABN Front Wheel Drive Axle Pulley Attachment - CV Axle Removal Tool CV Joint Slide Hammer Adapter

  • Use lubricant fluid for added ease (not included).
  • [Safe for Your Vehicle] Unlike pry bars or CV axle fork tools, the CV shaft slide hammer axle attachments focus the added torque to the back of the housing to prevent damage to the roller bearing inside the joint.
  • Pulls CV joints on 1986-current Taurus/Sable.
  • [Built to Last] Heat-treated CV puller adapter with black oxide finish ensures optimal strength and durability while resisting rust and corrosion.
  • Inner CV axle removal tool has 48mm (roughly 2-inch) opening and a 2.5-inch depth to fit your needs.
Check Stock

Inner CV Joint Puller Slide Hammer Front Wheel Drive Axle Half Shaft Removal Tool Kit CV Axle Removal Tool Slide Hammer 63mm 48mm CV Joint Fork Adapter Attachments

  • ⚒️ Quick to Remove CV Axle ⚒️ - With this CV axle removal tool the axle assembly is popped out of trans axle, and install the new axle,not need spend a lot of effort. Without damage to transmission case or inside roller bearing..
  • ⚒️ Perfect Joint Fork ⚒️ - This slide hammer puller set includes opening 63mm and 48mm CV joint fork disassembly adapter, the CV Joint Fork is be threaded internally, and the Slide Hammer stick is threaded externally. the joint fork could fit on the slide hammer stick, 63mm and 48mm fit most vehicle models, have wide use..
  • ⚒️ Heavy Duty ⚒️ -This slide hammer weighs 10.5 pounds and is 19.5 inches long, which is larger than the normal ones. So it has enough length to slide to generate more force, easier to use and work better.The hammer and VC joint fork are made of heavy-duty steel, durable and not easy to break..
  • ⚒️ Easy to Use ⚒️ - You need to attach the inner CV axle puller to your axle slide hammer, then place the adapter around the axle after the inner start. Slide the 10 lb. hammer weight back and forth to create torque and pull out the axle. Note: you can use....
Check Stock

CARTMAN 9-Way Internal/External Slide Hammer Puller Set - Pulls Hubs, Rear Wheel Axle Shafts, Bearings, Bushings, Seals, Retainers

  • Ideal for internal and external pulling on bearing cups, stubborn oil seals, Bushings, and many press fitted parts. Features: Internal and External Three Leg and Two Leg jaw puller yokes.
  • 5lb. Slide Hammer, 425mm long, M16*1.5mm UNF thread.
  • Front Hub puller, Rear Axle puller, Locknut Cone.
  • Dent puller screws (large and small), Supplied in blow mold storage case..
  • Features: Internal and External Three Leg and Two Leg jaw puller yokes..
Check Stock

JOMBULL 9-Way Slide Hammer Puller Set, 19 pcs Rear Wheel Axle Hub Dent Shaft Puller, Slide Hammer Bearing Puller for Hub Seal

  • 【Durable】 Our 9-way slide hammer puller set is made of heat-treated forged steel, polished and chrome-plated to resist rust and wear, extending the service life..
  • 【Application】 The axle hub dent shaft puller is widely used for flanged rear axles, most front wheel drive hubs, pulling dents and other press fit parts..
  • 【Easy to operate】 You only need to install the axle hub dent puller on the part you want to remove, when pulling the T-handle, transfer the force to the shaft, the shaft drives the connecting end to pull out the part, repeat the above steps, the hub or bearing will be easily removed..
  • 【What you get】 Our 9-way slide hammer puller set includes, slide hammer, puller head, pulling adapter, cross block, inner/outer pulling jaw, hex jaw nuts and screws (3pcs), Vise-Grip adapter (single lead thread), sealing hook, 3-way puller head, cone, self-tapping screw and retainer..
  • 【Safe storage】 The slide hammer bearing puller comes in a blow molded case, sturdy and durable, and each piece has precisely sized compartments, easy to store and carry..
Check Stock

VCT 23" Long 5lb Slide Hammer Inner CV Joint Puller

  • The set includes a 23-inch T-style slide hammers bar, a 5 lb hammer weight, a nut, and a 2-inch opening 2.5-inch depth slide hammer CV axle adapter. They will remove the axle assembly without damage on 1986 to current Taurus and Sable..
  • The slide hammer and puller design provide a straight and even pull to protect joint off damage. The round bead on the puller will stop the hammer so it can never hurt the hand pulling on T-shaped handle..
  • Our CV joint puller adapter and large slide hammer bearing puller will create added torque to impose a large pressure on CV axle. This tool set could easily loosen and remove stubborn CV axles in minutes..
  • The product is made of premium steel, all the parts have hardened and finished with high-temperature oxide to ensure superior durability and rust and corrosion resistance..
Check Stock

OMT Bearing Puller Set 5 Ton Capacity Bearing Separator Pinion Wheel Bearing Removal Kit with 2 and 3 Jaws Wheel Hub Axle Puller Set Heavy Duty Bearing Splitter Tool Kit with Case

  • VERSATILE BEARING PULLER: This Orion Motor Tech bearing puller set enables you to complete a wide range of pulling jobs, ideal for removing large or small bearings on front and rear wheel hub axle shafts, as well as gears, pulleys, and steering wheels.
  • ALL-IN-ONE TOOL KIT: Our bearing separator set includes a 3" bearing separator jaw, 2" bearing separator jaw, 6" yoke, 6-1/4" forcing screw, four 4" extension screws, four 5" extension screws, and two 4-1/2" L-type legs.
  • WIDE APPLICATION: The 2 bearing splitter jaws’ 5 ton capacity ensures they stand up to punishing use.
  • suitable for professionals and home mechanics and compatible with most vehicles, ATVs, and light trucks.
  • EFFECTIVE OPERATION: The knife like taper feature allows the jaws to get behind bearings to securely grip any bearing.
  • the included tools enable you to reach and remove bearings in tight spaces effectively.
  • DURABLE CONSTRUCTION: Constructed from heat treated Cr-V steel with black oxide finish, this pinion bearing puller set ensures corrosion resistance and long-term durability under even punishing use.
Check Stock

ATPEAM 9-Way Slide Hammer Puller Set | Wrench Adapter Axle Bearing Hub Auto Set, Axle Front Rear Wheel Bearing Dent Hub Gear Puller Remover Set

  • Extra Durable: The ATPEAM slide hammer puller set is made of drop forged steel pullers and fully hardened shaft and accessories, this will pull the hardest wheel bearing and wheel hub out of the tight position, and make sure this tool set a longer lifespan..
  • A Complete Puller Set: 1x shank and T-bar assembly, 1x 4.8 lb. sliding hammer weight, 1x cross nut, 2x hub grappler adapter flanges, 1x large forcing screw, 1x cone, 1x 3-way puller head, 1x vise grip adapter with double lead thread, 1x seal hook adapter, 1x dent puller retainer, 1x self-tapping screw, 3x 5 inch (127 mm) internal and external jaw bars, 3x hex jaw nuts, 3x hex head cap screws, and 1x blow molded storage case..
  • Auto Body Repair Tool Set: The slide hammer bearing puller kits are body shop tools that are used to aggressively remove tightly jammed parts or dents.
  • slide hammers consist of a long metal shaft with an attachment point at one end, a heavyweight that slides along the shaft, and a handle with a stop on the opposite end.
  • this hammer tool slide kit includes 2 jaws and 3 jaw internal and external pullers, rear axle bearing puller tool, locking plier adaptor, puller hook, and auto dent puller tool.
  • Wide Application: The 9-way slide hammer puller set with 4.8 lb slide hammer is idea....
Check Stock

E-cowlboy Inner CV Joint Puller Slide Hammer Front Wheel Drive Axle Half Shaft Removal Tool Kit,63mm 48mm CV Joint Fork Adapter,Heavy Duty 10 Pounds Slide Hammer

  • ...versal joint slide hammer to work more efficiently..
  • 【Quick to Remove CV Axle 】：With this CV axle removal tool the axle assembly is popped out of trans axle, and install the new axle,not need spend a lot of effort. Without damage to transmission case or inside roller bearing..
  • 【100% SATISFACTION GUARANTEE 】If you're not 100% satisfied with this tool, simply return it for a full refund in 30 days. Premium Support & 12-Month Warranty..
Check Stock

Sunluway - 12020-2 Pack Axle Popper Kit - Inner CV Axle Removal Tool Set - for Use on Front Wheel Drive Vehicles-Remove Most Vehicles’ Half-Shaft Drive Axles-Fix Damaged CV Joints

  • Easy to disassemble: Skip the complicated slide hammer puller sets and pry bar tools that can cause damage to your axle, use this CV shaft tool to easily disassemble the CV shaft, saving your time and energy !.
  • Material: CV Axle Removal Tool Set made of high-strength hardened steel, which has high hardness, high strength, with stable performance and reliable use and longer service life.
  • Benefits: Better and Safer than Using a Hammer and Bar because the wedge-shaped fork end of the axle Popper applies uniform pressure to both sides of the shaft To ensure safe release (Two piece CV axle popper tool kit ensures fitment for most FWD vehicles).
  • Easy installation: Insert the wedge wheel bearing tool between the transaxle case and the axle joint, and the fork head surrounds the axle end, tap the end of the front fork to release the axle shaft. these axle puller tools are simple, yet powerful, Is your essential tool !.
  • 100% Satisfaction Guarantee: If you're not 100% satisfied with our , please feel free to contact us, simply return it for a full refund in 30 days. Premium Support & 12-Month Warranty..
Check Stock