Reviews Axial Contact Bearing

CBRIGHT 2 Pieces 6mm Female Thread Connector Bearing Steel Joint Rod End Bearing

  • Products can withstand radial load,Axial load or radial. Axial simultaneous joint load..
  • Due to the inner surface of the spherical inlaid composite material,therefore, the bearing in the work can produce self-lubricating..
  • Use: Joint bearings are widely used in engineering hydraulic cylinders, forging machine tools, engineering machinery, automation equipment, automotive shock absorbers, water conservancy machinery, etc..
  • 2 Pieces 6mm Female Thread Connector Joint Rod End Bearing.
Check Stock

CBRIGHT 4 Pieces 6mm Female Thread Connector Bearing Steel Joint Rod End Bearing

  • Products can withstand radial load,Axial load or radial..
  • Product Material: bearing steel. Axial simultaneous joint load..
  • Use: Joint bearings are widely used in engineering hydraulic cylinders, forging machine tools, engineering machinery, automation equipment, automotive shock absorbers, water conservancy machinery, etc..
  • Due to the inner surface of the spherical inlaid composite material,therefore, the bearing in the work can produce self-lubricating..
  • 4 Pieces 6mm Female Thread Connector Joint Rod End Bearing.
Check Stock

General Motors 12643668, Engine Crankshaft Thrust Washer

  • Thrust washers limit axial movement and provide a bearing surface. Thrust bearings are designed to support axial load..
  • Thrust washers either have multiple tapered ramps and relatively small flat pads or have curved surfaces that follow a sine wave contour around their circumference..
  • Tear-drop or through grooves on the flange faces and wedge shaped ramps at each parting line allow engine oil to enter between the shaft and bearing surfaces..
  • Manufactured to meet or exceed OE specifications.
Check Stock

Clevite TW-678S Engine Crankshaft Thrust Washer Set

  • Thrust washers limit axial movement and provide a bearing surface. Thrust bearings are designed to support axial load..
  • Thrust washers either have multiple tapered ramps and relatively small flat pads or have curved surfaces that follow a sine wave contour around their circumference..
  • Tear-drop or through grooves on the flange faces and wedge shaped ramps at each parting line allow engine oil to enter between the shaft and bearing surfaces..
  • Manufactured to meet or exceed OE specifications.
Check Stock

Clevite TW-473S Engine Crankshaft Thrust Washer Set

  • Thrust washers limit axial movement and provide a bearing surface. Thrust bearings are designed to support axial load..
  • Thrust washers either have multiple tapered ramps and relatively small flat pads or have curved surfaces that follow a sine wave contour around their circumference..
  • Tear-drop or through grooves on the flange faces and wedge shaped ramps at each parting line allow engine oil to enter between the shaft and bearing surfaces..
  • Manufactured to meet or exceed OE specifications.
Check Stock

Bzsunway 696ZZ 6mm x 15mm x 5mm Double Shielded Pre-Lubricated Miniature Deep Groove Ball Bearing (20pcs)

  • 【Wide Application】 Used to accommodate radial and axial loads in both directions. Suitable for all kinds of industrial equipment, micro motor, small rotary motor, office equipment, electric motors,band raw ,skateboard..
  • 【Protective shields】 Fitted with two steel dust shields in the outer ring of the bearing to protect the working parts of the bearing from the influence of debris that may be introduced, especially useful in high temperature applications and where low torque is required..
  • 【Superior Quality】 Our 696ZZ deep groove ball bearing are made from high-quality chrome steel, durability and resistance to under heavy loads.  .
  • 【Bearing Features】 With small friction and high-limit speed，the bearing is low vibration, low noise, high precision. Use rolling elements to maintain the separation between moving parts to reduce rotational friction and support radial and axial loads,.
  • 【Satisfactory Service】 If you are not satisfied with our products.You can request a full refund within 30 days to support a 12 month warranty.Professional and sincere service allows you to purchase without risk !.
Check Stock

MOCHU 725 725C/P5 5x16x5 Angular Contact Ball Bearing, ABEC-5, 15° Contact Angle, Metric, 5mm ID, 16mm OD, 5mm Width, Single Row, Open

  • Double-row angular contact ball bearing, supporting moderate combined radial and bidirectional thrust loads.
  • Ball contact angle of 20 degrees relative to the inner and outer raceways increases thrust load capacity.
  • Rubber seals on both sides of the bearing to keep lubricant in and contaminants out.
  • Pressed steel cage evenly spaces balls for reduced friction, vibration, and noise.
  • Normal axial internal clearance for applications where thermal expansion is not a factor.
Check Stock

NSK 6806DD 6806-2RS Made in Japan 30x42X7MM High Speed Bearings Deep Groove Ball Bearings

  • Deep-groove geometry for high speeds and supporting both radial and axial loads.
  • Single-row bearing for supporting radial loads.
  • Normal radial internal clearance for applications that do not involve thermal expansion or atypical precision.
  • Pressed steel cage evenly spaces the balls for even load distribution and prevents contact to reduce friction, vibrations, and noise.
  • Shields on both sides of the bearing to keep lubricant in and contaminants out.
Check Stock

NTN Bearing 30206 Tapered Roller Bearing Cone and Cup Set, Steel, 30 mm Bore, 62 mm OD, 17.25 mm Width

  • 30206 Bearing Size: Out Diameter:62mm/2.44 inch.
  • Ealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use.
  • Complete single tapered roller bearing assemblies are generally mounted in opposing pairs on a shaft to evenly distribute loads..
  • They incorporate logarithmic roller and raceway profiles with a optimized surface finish for ultimate roller to flange contact. These features result in reduced noise and smooth operation..
  • Widely used in transmissions, span styleoil or greased, high radial and axial load, trailer and caravan axles, gearboxes and differentials, span..
Check Stock

Mardatt 24 pcs 3 Type Thrust Needle Roller Bearings with Washers, AXK3552, AXK2035, AXK2542 Chromium Steel Rollers for Automobiles, Pump, Machine Tools

  • 【3 Size Thrust Needle Roller Bearing Assortment】You will get 9 pcs 20*35*2MM thrust needle roller bearings with washers, 9 pcs 25*42*2MM thrust needle roller bearings with washers, 6 pcs 35*52*2MMthrust needle roller bearings with washers, totally 24 pcs..
  • 【Premium Material】Made of chromium steel featured with a nice load carrying capacity and stiffness, high hardness, and high precision, smooth surface no residual burr that smooth to touch. Heat treatment process makes the bearing ball stronger, avoiding to deformed for a long time..
  • 【Feature】Needle Roller Thrust Bearings can accommodate axial loads in one direction only. Low noise and long service life, easy to maintain. Keep the bearing working environment clean and bearing lubricated in time..
  • 【Huge Function】Designed for low speed operation and axial loads only. Steel cage guides and evenly spaced rollers for reduced friction, vibration, and noise..
  • 【Wide Application】 Combined with 2 washers, make objects rotating smooth! Perfect for oven turntable, pump, rotating applications, motors, bikes, air conditioning, machine tools, automobiles, ect..
Check Stock

Dayton 2LY99 Air Circulator, 20 In

  • Dayton 4WT47 Axial Fan With 4YD87A Fan Cover, 115VAC 60/50Hz, 0.18/0.21A, 18/20W.
Check Stock

RBC JHA15XL0 Thin Section Ball Bearing, Sealed, 4-Point Contact X-Type, 1.5\ Bore x 1.875\ OD x 0.25\ Width

  • X-type 4-point contact ball bearing for use where space is limited and moment loads are high.
  • Deep-groove geometry for high speeds and supporting both radial and axial loads.
  • 52100 steel races and bearing balls for durability and resistance to deformity under heavy loads.
  • Conforms to ABEC 1F precision standard for performance within a narrow range of variation.
  • Rubber seals to retain lubricant and for protection against contaminants.
Check Stock

SKF 22207 E/C3 Spherical Roller Bearing

  • Shaker screen two row spherical roller bearing suitable for applications that support radial and oscillating axial loads.
  • Machined brass cage spaces the rollers for even load distribution and prevents contact to reduce friction, vibration, and noise.
  • P5 precision outer ring with center lubrication groove and oil holes.
  • C4 radial clearance is larger than CN and C3 for applications where impact loads and vibration are severe, both the inner and outer rings are tight fitted, or thermal expansion is a factor.
  • Straight bore fits conventional cylindrical shafts.
Check Stock