Reviews Astm Angle Steel Bar

DuroSTEEL Janus 10'x9' Commercial 1000 Series Metal Roll Up Door & Hardware Direct

  • ...r a nominal upcharge). Super Durable Polyester paint coatings, which are corrosion resistant. Wash coat over primer interior side. 40-year film integrity warranty — up to 25-year chalk and fade. Flexible nylon wear strips..
  • Bottom Bar: 24 gauge acrylic-coated galvalumed roll formed steel. 2” x 1 ½” galvanized angle. Bulb astragal (Durometer 75). Stainless steel bolts..
  • Axel/Torque Tube: 1” O.D. steel axle, 12-gauge. Oil tempered torsion springs conforming to ASTM A229. 18-gauge, 9 ½” diameter galvanized drum. Low friction, grease-filled steel ball bearings staked in each drum. 26 gauge spiral torque tubing that houses axle assembly..
  • Guide: 16 gauge galvanized. Vinyl guide wear strip. Bolt on head stop ¼” thick steel. 2 ¼” guide dept. Pre-punched for lock. Universal jamb mount. Hardware: Bottom bar mounted 12 gauge slide locks - 2 per door. Bottom bar mounted 16 gauge step plate - 2 per door. 12 gauge door mounting brackets. Ratchet tensioner device..
Check Stock

DuroSTEEL Janus 10'x12'Commercial 1000 Series Metal Roll Up Door & Hardware Direct

  • ...r a nominal upcharge). Super Durable Polyester paint coatings, which are corrosion resistant. Wash coat over primer interior side. 40-year film integrity warranty — up to 25-year chalk and fade. Flexible nylon wear strips..
  • Bottom Bar: 24 gauge acrylic-coated galvalumed roll formed steel. 2” x 1 ½” galvanized angle. Bulb astragal (Durometer 75). Stainless steel bolts..
  • Axel/Torque Tube: 1” O.D. steel axle, 12-gauge. Oil tempered torsion springs conforming to ASTM A229. 18-gauge, 9 ½” diameter galvanized drum. Low friction, grease-filled steel ball bearings staked in each drum. 26 gauge spiral torque tubing that houses axle assembly..
  • Guide: 16 gauge galvanized. Vinyl guide wear strip. Bolt on head stop ¼” thick steel. 2 ¼” guide dept. Pre-punched for lock. Universal jamb mount. Hardware: Bottom bar mounted 12 gauge slide locks - 2 per door. Bottom bar mounted 16 gauge step plate - 2 per door. 12 gauge door mounting brackets. Ratchet tensioner device..
Check Stock

DuroSTEEL Janus 8'x10' Insulated Commercial 1000i Series Metal Roll Up Door & Hardware Direct

  • ...r a nominal upcharge). Super Durable Polyester paint coatings, which are corrosion resistant. Wash coat over primer interior side. 40-year film integrity warranty — up to 25-year chalk and fade. Flexible nylon wear strips..
  • Bottom Bar: 24 gauge acrylic-coated galvalumed roll formed steel. 2” x 1 ½” galvanized angle. Bulb astragal (Durometer 75). Stainless steel bolts..
  • Axel/Torque Tube: 1” O.D. steel axle, 12-gauge. Oil tempered torsion springs conforming to ASTM A229. 18-gauge, 9 ½” diameter galvanized drum. Low friction, grease-filled steel ball bearings staked in each drum. 26 gauge spiral torque tubing that houses axle assembly..
  • Guide: 16 gauge galvanized. Vinyl guide wear strip. Bolt on head stop ¼” thick steel. 2 ¼” guide dept. Pre-punched for lock. Universal jamb mount. Hardware: Bottom bar mounted 12 gauge slide locks - 2 per door. Bottom bar mounted 16 gauge step plate - 2 per door. 12 gauge door mounting brackets. Ratchet tensioner device..
Check Stock

STEELWORKS BOLTMASTER 11687 Flat Steel Bar 1/4 x 1-1/2 x 48

Check Stock

Hot Rolled Steel Plate 1/2\ x 4\ x 4\ (Pack of 2!)

Check Stock

VEVOR Hydraulic Rebar Bender, 1700W, Electric Rebar Bender and Cutter, 1''/25 mm Max Rebar Diameter, Rebar Steel Bender and Cutter Machine, Bending Machine For Bending Rebar, Steel Bar, Steel Rod

  • Ultra-Fast Working Speed: This rebar bender and cutter machine is designed with excellent performance. It helps save valuable person-hours by bending rebar 1/4'' #2 to 1" #8 Grade 60(6 to 25 mm) within 6 to 7 seconds. It can also cut rebar within 5-6 seconds. Bending Angle: 0-180°. Bending Radius: 1.57'' / 40 mm, Max. Rebar Hardness: HRC30, Hydraulic Oil Type: VG46..
  • 1700W Pure Copper Coil Motor: This rebar cutter and bender features a 1700W pure copper motor, which can run quietly with low noise and significantly improve your working efficiency, reducing unnecessary wear. Besides, a copper motor can extend this rebar bender cutter's operating life to a large extent. Voltage: 110V, Frequency: 60 Hz, Amps: 14A, Noise: 92 dB(A)..
  • Angle Adjustment Knobs: This rod bending machine has two slide-type angle selectors, which can help you accurately bend any angle from 0-180 degrees. Preset angle locks are designed for repeating the same angle bending. When bending processing, the angle of point 1 must be bigger than point 2. Otherwise, the machine can not operate normally..
  • Sturdy Machine Body: The bar bender machine adopts a sturdy iron machine body and durable Idler Wheel. Ø78 iron Gyre Idler Wheel and Ø94 Fixed Idler Wheel are stronger and not easy t....
Check Stock

VEVOR Hydraulic Rebar Bender 1700 Wattage Electric Rebar Bender and Cutter, 1''/25 mm Max Rebar Diameter, Rebar Steel Bender and Cutter Machine, Bending Machine For Bending Rebar, Steel Bar, Steel Rod

  • Ultra-Fast Working Speed: This rebar bender and cutter machine is designed with excellent performance. It helps save valuable person-hours by bending rebar 1/4'' #2 to 1" #8 Grade 60(6 to 25 mm) within 6 to 7 seconds. It can also cut rebar within 5-6 seconds. Bending Angle: 0-180°. Bending Radius: 1.57'' / 40 mm, Max. Rebar Hardness: HRC30, Hydraulic Oil Type: VG46..
  • 1700W Pure Copper Coil Motor: This rebar cutter and bender features a 1700W pure copper motor, which can run quietly with low noise and significantly improve your working efficiency, reducing unnecessary wear. Besides, a copper motor can extend this rebar bender cutter's operating life to a large extent. Voltage: 110V, Frequency: 60 Hz, Amps: 14A, Noise: 92 dB(A)..
  • Angle Adjustment Knobs: This rod bending machine has two slide-type angle selectors, which can help you accurately bend any angle from 0-180 degrees. Preset angle locks are designed for repeating the same angle bending. When bending processing, the angle of point 1 must be bigger than point 2. Otherwise, the machine can not operate normally..
  • Sturdy Machine Body: The bar bender machine adopts a sturdy iron machine body and durable Idler Wheel. Ø78 iron Gyre Idler Wheel and Ø94 Fixed Idler Wheel are stronger and not easy t....
Check Stock

KES Shower Slide Bar for Bathroom with Adjustable Handheld Shower Holder Wall Mount SUS 304 Stainless Steel Matte Black, F204-BK

  • SUS304 Stainless Steel: Sliding bar and posts are made of stainless steel, durable and rust-proof. The extra-thick bar will not be bent nor dent from day to day use..
  • Adjustable Bracket:: Engineering grade ABS material shower bracket, allows you to adjust any height or angle of handheld shower head after installation. Shower height and angle can be easily adjusted to accommodate both kids and adults, providing perfect shower experience for every family member..
  • Wall-Mounted Installation: Use screws and anchors in the package to install this slide bar. Drill-bit size is 6mm. Screws are made from SUS 304 stainless steel and won't rust..
  • Matte Black Finish: Perfectly smooth, high quality matt black finish is built to resist daily scratches, corrosions, and tarnishing..
  • Installation Instruction Included: Package includes slide bar, shower holder, hardware pack, and a detailed installation guide. NOTE: Showerhead and shower hose are not included. If you need those, please search for B085KXGSCJ..
Check Stock

Valhalla Custom Kydex Sheath Ka-bar Becker BK9 COYOTE BROWN One Piece

  • Knife Made in the USA, Sheath made in Taiwan.
Check Stock

Accusize Industrial Tools 3/8'' by 4.33'' Right-Hand Sclcr Coolant Through Indexable Boring Bar with Ccmt Insert 21.51, 2800-0035

  • General purpose boring bar fitted with rhomboidal positive inserts (80°angle) which are free cutting with strong cutting edges..
  • The coolant hole with a diameter range varying between 3/32" and 5/32" in accordance to the bar size allows to cool the cutting edge and remove chips..
  • The inserts is set with a 0° rake angle and an inclination angle shown in the table below..
  • Made of tool steel with nitrogen superficial treatment, Hardness 60 HRC, blackening by PVD coating, thickness 0.0002"..
  • Extreme gloss finish, Bar hardness approximately 45HRC.
Check Stock

Advantech - 10SS8F Stainless Steel Test Sieves, 8\ Diameter, #10 Mesh, Full Height

  • Stainless Steel frame, stainless steel wire cloth.
  • Full height (2 inch depth to wire cloth).
  • Serial number is etched on each sieve and contained in a bar-coded label, tracing vital information.
  • Comes with Certificate of Compliance applicable to ASTM E 11 specifications.
Check Stock

RIMKOLO Pry Bar Set,5-Piece Heavy Duty Pry Bar with Thicker Strike Caps,4-Piece with Angled Tip and 1-Piece with Straight Tip

  • 【APPLY TO ANY SPACE】: Sharp angle tip, easy to enter the narrow gap. The combination of angle head and straight head is more convenient and widely used..
  • 【WITH STRIKE CAP】: Ergonomic handle, comfortable and antiskid. The end of the handle is provided with a strike cap, which allows the pry bar to be struck into place with a hammer..
  • 【SOLID】: Made of high-quality chrome vanadium steel, which is harder after heat treatment and not easy to distort and deform. The crowbar with proper proportion length is more labor-saving..
  • 【DURABLE】: The pry bar surface is protected by black oxide film, Anti corrosion and anti rust, extending service life. Thicker crowbar, stronger and more durable..
  • 【5-PIECE PRY BAR SET】: 4x Angle head pry bar: 8" 12" 18" and 24.
Check Stock

ADVANTECH - 80SS8F Advantech Stainless Steel Test Sieves, 8\ Diameter, #80 Mesh, Full Height

  • Stainless Steel frame, stainless steel wire cloth.
  • Full height (2 inch depth to wire cloth).
  • Serial number is etched on each sieve and contained in a bar-coded label, tracing vital information.
  • Comes with Certificate of Compliance applicable to ASTM E 11 specifications.
Check Stock