Reviews Arduino Gsm Shield 4g

HiLetgo 3pcs 400 Ties Mini Solderless Breadboard Universal 400 Contacts Solderless Breadboard 400 Points Prototyping Shield for Electronics Testig DIY

  • 400 Points Breadboard with 2 Positive & Negative Power Lines on both ends.Perfect for Arduino Shield Prototyping and Testing..
  • Insertion Wire Size is 21 to 26 AWG, 0.016 to 0.028 inches diameter (0.4 to 0.7mm diameter),works with dupont jumper wires kit..
  • White ABS body with black printed legend. Color legend on distribution strips..
  • With self-adhesive tape on the back, make it easy to stick on the Arduino Prototype Shield..
  • Good kits for Arduino breadboard kit proto shield and DIY projects..
Check Stock

ACEIRMC 2pcs 1602 LCD Keypad Shield 1602 LCD Expansion Shield Board Blue Backlight 4.5-5.5V for Arduino R3 MEGA2560 Nano Due Duemilanove Robot (5pcs)

  • 1602 LCD Shield Module Display V3 for Arduino R3 MEGA2560 Nano DUE.
  • This is a 16x2 LCD Keypad module for Arduino Diecimila Duemilanove,MEGA1280, MEGA2560 board..
  • Blue Backlight with white words, adjustable backlighting.
  • 4 Bit LCD Library,V3 design, pins out for easy connecting.
  • 1602 LCD Keypad Shield 1602 LCD Expansion Shield Board Blue Backlight 4.5-5.5V for Arduino Duemilanove Robot.
Check Stock

HiLetgo 5pcs Nano IO Shield DIY Nano IO Expansion Board DIY Kits for Arduino Nano

  • Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step.
  • New Expansion Board Terminal Adapter DIY Kits for Arduino NANO IO Shield V1.0.
  • Leads all pins out, convenient for wiring and doing experiments.
  • IO Expansion Shield For Arduino Nano is specifically designed to facilitate.
  • In essence, it expands for Arduino Nano controller to link those devices in a simple and trouble free manner..
Check Stock

Ingcool 4G/3G/GNSS HAT Module for Raspberry Pi 4B/3B+/3B/2B/Zero/Zero W/Zero WH,Jetson Nano, Based on SIM7600A-H, 4G/GNSS Module Support LTE CAT4 up to 150Mbps for Data Transfer, etc.

  • SIM7600A-H 4G HAT is a 4G/3G communication and GNSS positioning module, supports LTE CAT4 up to 150Mbps for downlink data transfer. it is pretty low power consumption.
  • Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi 4B/3B+/3B/2B/Zero/Zero W/Zero WH series boards, Compatible with Jetson Nano, SIM7600A-H 4G module control pins can connect with host boards like Arduino/STM32.
  • Supports dial-up, telephone call, SMS, mail, TCP, UDP, DTMF, HTTP, FTP, etc. Supports GPS, BeiDou, Glonass, LBS base station positioning.
  • Connect the 4G module with computer to surf the Internet, or attach it onto Raspberry Pi to enable functions like 4G high speed connection, wireless communication, making telephone call, sending SMS, global positioning, etc..
  • Comes with development resources and manual (examples for Raspberry Pi/Jetson Nano/Arduino/STM32).
Check Stock

EEEEE UNO R3 ATMEGA328P ATMEGA16U2 & Multi-Function Shield Starter kit (2 in 1) for Sensor WiFi Relay Bluetooth Module with Digital Display Switches with USB Cable Compatible with Arduino IDE

  • 1. Using this Ethernet shield, your for Arduino board can be used to connect to the Internet and can be used as a server or client..
  • 2. This Arduino Ethernet shield based on Wiznet W5100 Ethernet chip provides you with a way to easily get Arduino Online, because it is directly supported by the official Arduino Ethernet library..
  • 3. It adds a micro-SD card slot, which can be used to store files provided through the network..
  • It is compatible with Arduino Duemilanove (168 or 328), Uno and Mega (1280/2560) and can be accessed using the SD library..
  • 4. Wiznet W5100 provides a network (IP) stack that can support both TCP and UDP..
Check Stock

Gikfun Prototype Shield DIY Kit A1 for Arduino Mega 1280 2560 R1 - R3 (Pack of 2pcs) EK1096x2

  • Prototyping Shield Diy Kits. Great for building your own designed Arduino Uno sheilds..
  • You can solder parts to the prototyping area to create your project, or use it with a small solderless breadboard to quickly test circuit ideas without having to solder..
  • It's got extra connections for all of the Arduino MEGA 1280 / 2560 R1 R2 R3 pins, and it's got space to mount through-hole and surface mount integrated circuits..
  • The Prototyping Shield makes it easy for you to design custom circuits..
  • It's a convenient way to make your custom circuit and Arduino into a single module..
Check Stock

Arduino MKR GPS Shield [ASX00017]

  • A plug 'n' play shield for experimenting with monitoring fleets, high-altitude measurements, or any kind of project requiring localization of devices..
  • Arduino MKR GPS Shield uses the u-blox SAM-M8Q GNSS (Global Navigation Satellite System) module. It is meant to be used on top of boards in the Arduino MKR boards, but thanks to its Eslov connector, it is also possible to hook it up to any board..
  • It comes with a dedicated library that allows two different interfaces and offers a consistent set of APIs designed for a full usage of the GPS acquired information..
  • Operating voltage is 3.3V, but this shield comes also with an on-board holder for CR1216 batteries..
  • The MKR GPS Shield has an additional connector meant as an extension of the I2C bus. The extra I2C port, also referred to as the Eslov self-identification port comes with: SDA, SCL, GND, +5V, and an extra digital pin, meant to send an alarm to the otherwise plain I2C devices connected to it..
Check Stock

ACEIRMC 6pcs Nano V3.0 3.0 Controller Terminal Adapter Expansion Board Nano IO Shield Simple Extension Plate for Arduino Mano AVR ATMEGA328P

  • Designed for Arduino for Nano V3.0: The item is a terminal expansion adapter, working very well for prototyping Arduino for Nano projects.
  • It lables for Arduino for Nano version 3.0, however you can still use this adapter for the older version (just have to remember that A0-A7 are in the reverse order)..
  • You can use this adapter to easily hook up for arduino for Nano to an outside world via hook up wires.
  • This item is a terminal expansion adapter, designed for Arduino Nano V3.0..
  • Nano Terminal Adapter Shield Expansion Board Compatible with Arduino Nano V3.0 AVR ATMEGA328P-AU Module.
Check Stock

2Pack 9V Battery Clip Connector Cable with Holder Box for Arduino UNO R3 Mega 2560 Power Module 6F22 6LR61 mn1604 pp3 Baterries

  • Standard 5.5x2.1mm Center Positive Barrel Jack DC Male Plug. Cable length: Approx. 20cm (7.8 inch)..
  • Widely Used for Arduino Uno, Arduino Due, Arduino Mega 2560, Arduino Ethernet Shield, development boards, evaluation boards, breadboard, Arduino DIY, DSO 138 OscillOscope kit, XR2206 function generator and the device which need the 9V battery..
  • Easy install & Save work: This cable come with a 9V battery holder and 3 screw fixing hole on the base, convenient for fixing.
  • With this snap cable, you can saves the work of soldering a battery snap to a DC coax plug. Don't always have to take apart/open some test equipment just to change the battery inside..
  • ! ! ! Not fit for Arduino Nano, Effect pedals..
  • Any quality issues, please feel free to contact us..
Check Stock

SunFounder Mega 2560 R3 ATmega2560-16AU Board and Ethernet Shield W5100 for Arduino

  • The mega 2560 R3 Board is 100% compatible with Arduino. Powered via the USB connection or with an external power supply. The power source is selected automatically..
  • The ATmega2560-16au has 256 KB of flash memory for storing code (of which 8 KB is used for the bootloader), 8 KB of SRAM and 4 KB of EEPROM (which can be read and written with the EEPROM library)..
  • The mega 2560 comes preburned with a bootloader that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the original STK500 protocol (reference, C header files).This version is optimized in the original version, both to ensure consistent and compatible with the original, but also easy to use..
  • With this Ethernet Shield, for Arduino board can be used to connect to internet. It can be used as server or client. Directly plug puzzle board, no soldering required..
  • This Ethernet Shield is directly compatible with Arduino official Ethernet Library. It adds a micro-SD card slot, which can be used to store files for serving over the network..
Check Stock

6Pack 9V Battery Clip Connector Cable with Holder Box for Arduino UNO R3 Mega 2560 LED Strip Light Power Module 6F22 6LR61 mn1604 pp3 Baterries

  • Widely Used for Arduino Uno, Arduino Due, Arduino Mega 2560, Arduino Ethernet Shield, development boards, evaluation boards, breadboard, Arduino DIY, DSO 138 OscillOscope kit, XR2206 function generator and the device which need the 9V battery..
  • Easy install & Save work: This cable come with a 9V battery holder and 3 screw fixing hole on the base, convenient for fixing.
  • With this snap cable, you can saves the work of soldering a battery snap to a DC coax plug. Don't always have to take apart/open some test equipment just to change the battery inside..
  • Standard 5.5x2.1mm Center Positive Barrel Jack DC Male Plug. Cable length: Approx. 20cm (7.8 inch)..
  • Not fit for Arduino Nano, Effect pedals..
  • Any quality issues, please feel free to contact US..
Check Stock

9V Battery Holder E-outstanding 2PCS Black 6F22 9V Battery Storage Case Box with 2.1x5.5mm DC Male Plug and Wire Leads for Arduino UNO R3 Battery Clip Container

  • Made of high quality materials. Lightweight and easy to carry..
  • Designed with spring clips for easy battery installation and removal..
  • EASY TO INSTALL AND SAVE WORK: The cable comes with a 9V battery holder and 3 screw fixing holes on the base for easy fixation.
  • With this snap cable you can save yourself the work of soldering the battery snap to the DC coax plug.
  • Widely used in Arduino Uno, Arduino Due, Arduino Mega 2560, Arduino Ethernet Shield, Development Boards, Evaluation Boards, Breadboards, Arduino DIY,....
Check Stock

Screw Terminal Block Breakout Shield Module for Arduino UNO R3

  • Terminal Block Breakout Shield Module - for Arduino UNO R3. the item has been soldered and assembled..
  • Terminal block pitch 3.5mm/0.138", wire size range 26AWG to 16AWG, strip length 5mm, screw M2 steel, pin header and cage copper..
  • Standard IDC40 pitch 0.1" header, you can use 40pin FRC(flat ribbon cable) connector cable connect all Arduino Uno pins to peripheral equipment..
  • With power on LED indicating. red reset button on the side. with a ICSP adapter connect header. FR-4 fiber glass PCB, dual copper layers..
  • NOTE: the item not include Arduino Uno module..
Check Stock