Reviews Anet Aheated Bed

BIQU Flexible Removable PEI Steel Sheet Heated Bed with Magnetic Sticker 220x220mm, Build Surface Platform for Anet A8 Robo R2 Anet A8 A6, Robo R2, Wanhao Duplicator6, Wanhao i3 3D Printer

  • Suitable for Anet A8 Robo R2 Anet A8 A6, Robo R2, Wanhao Duplicator6, Wanhao i3 3D Printer Original Removable PEI Steel Sheet Heated Bed..
  • Heated bed Platform: Easy to Use and Flexible, which has certain flexibility and can be bent. After cooling, the model is loose and easy to take..
  • Magnetic Sticker:The build surface has an upper magnetic build surface and a lower magnetic adhesive base. Place the 3M lower adhesive surface on a common construction board..
  • High temperature resistance: Withstand temperature above 200 ℃..
  • After-sales support: If you encounter any problems, please write us via Amazon-Email. We are happy to answer all your questions..
Check Stock

BIQU Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer

  • A general add-on heated bed power expansion module for 3D printer.
  • Completely solve the hot bed power is too large and the load current issue. It can work with the Anet A8.
  • With this addon module to your 3D printer motherboard you can lead the maximum current up to 15A.
  • Under the premise of normal heat dissipation, this module can work steadily under the condition of I(Max)=15A. Don't exceed 15A during the process.).
  • If you intend to use heated bed with your 3D printer that uses a 12V power supply, then this module is recommended, else it may cause excessive....
Check Stock

DOBSTFY 3D Printing Build Surface 3D Printer Heat Bed Platform Sticker Sheet 8 x 8 200x200mm Square - Pack of 4

  • 【PACK of 4】This 200x200mm (8"x8") Build Surface for Anet A8 WanHao i3 Detachable 3D Printers DYI, square, fully matches heated bed on many popular....
  • 【High Quality Material】High strength and heat resistance (up to 240°C) allows the 3D Printer surface to perform consistently in high temperature....
  • 【Easy to Install and Remove】Thick 1mm building plates will not warp or bend under heat. It is used on top of your heated print bed and provides....
  • 【Fully Compatibly】 This 3D Printer heatbed platform sheet allows for multiple uses with either the same or different filament material. Compatible....
  • 【SATISFACTION GUARANTEED】We're so confident that you'll love these premium print surfaces, that we offer lifetime technical support and 24 hours....
Check Stock

Anet 5pcs Thermistor NTC 3950 100K ohm Thermistor for RepRap 3D Printer Heatbed or Hot End 3D Printer Kit Accessories - White 5PCS

  • Anet ​3d printer 100k thermistor 1.2m can be used on both of the heated bed and the extruder for 3d printers.
  • The thermisor is compatible with most 3D printers in the market such as ender3, ender3 pro, ender3 V2, CR-10, hictop d3 hero eAnet 3d printer tc.
  • There is a 2 pin female connector on the thermistor for 3D printer.
  • Wire length for the thermistor: 1m/47 inches..
  • Recommended parameters for the thermistor: R25℃=100K.
Check Stock

Protech 51-102500-01 1/2 hp 120/1/60 Blower Motor

  • HIGH TORQUE: Adopting high quality motor steel material, DROK 3d printer stepper motor kit is provided with high torque (0.46 Nm/ 65 oz-in), low self-inductance reactance, responsive and can avoid system error..
  • LOW NOISE: The internal rotor of our anet anet a8 stepper motor kit is made with introduced German craftsmanship and there is rotor rubber covering the rotor, effectively reduce the noise..
  • DURABLE & TOUGH: Our mini motor uses high hardness metal, tough and durable. And the matte texture in the side wall can increase friction..
  • WIDE APPLICATION: This small motors can be used in various area, such as stage lighting.
  • WHAT YOU GET: The package includes 1* 42 Stepper Motor..
Check Stock

AITRIP 10PCS 3D Printer Removable 3950 NTC 100K Thermistor Sensor Compatible with Creality Ender 3 5 CR10 CR-10 CR10 Anet A8 Prusa i3 MK8

  • Temperature sensor 100KΩ accuracy of ± 1%, Total length:1 Meter.
  • Compatible with Creality CR-10S Pro,CR-X,Ender 3, Ender 3X, Ender-3 Pro, Prusa I3, Anet E10 etc.
  • AITRIP Thermistor Sensor is Removable design and Easy to install.
  • Package include: 10 thermistors. Threre is no HX2.54 connector at the end of the thermistor..
  • Use for heated bed or extruder of 3D Printer, with DuPont connectors..
Check Stock

PEI Sheet Magnetic Bed Flexible Spring Steel Platform with 3M Adhesive, 220x220mm（8.66 8.66inch) for Anet A8, A6, Robo R2, Wanhao Duplicator6, Duplicator i3 Monoprice Maker 3D Printers.

  • ...y moved if bend the Magnetic plate when the heated bed reaches room temperature. then just wipe the surface with isopropyl alcohol and it can be reused as new..
  • 【Practical Features】: Flexible, removable, high strength and heat resistance, good adhesion to PLA and ABS,220x220mm PEI sheet size is suitable for Anet A8,Cocoon 3D Printer, Wanhao Duplicator i3 V1/ Plus Monoprice Maker and similar size 3D printers..
  • 【 Notice】: There is a transparent protective film on the surface of the smooth PEI sheet spring steel build plate, which needs to be torn off before use. If there are bubbles on the film, it is not a quality problem, just tear it off, it will not affect the use.If you have any questions about product quality and suggestions, please feel free to contact us and we will reply within 24 hours..
Check Stock

3D Printer Glass Bed Upgraded, Borosilicate Glass Plate w/Corners Cut for Monoprice Maker Select V2 Anet A8/A6 Wanhao Duplicator i3 220x220x3mm with4 Glass Clips

  • 【Borosilicate Glass】 High binding power when heating. Easy to separate the plastic parts when cooling..
  • 【Size】 220mm x 220mm x 3mm.Compatble with Maker Select V2, Wanhao Duplicator, Anet A8, Anet A6 and other 3D Printers..
  • 【Safety】 Flat Polished Edge for safe to handle..
  • 【Hight quality 】Resistant to thermal shock compared to regular glass. A good build plate upgrade replacement..
  • 【Flat Enough】 Reduces warping, keep the printing surface level..
Check Stock

Anet GT2 Timing Belt with 16 Teeth Timing Pulley, 1PCS 1.7m PU Material with Steel Wire 6mm Timing Belt + 2PCS Bore 5mm 16 Teeth Timing Pulley for Anet A6 A8 3D Printer

  • Additonal positive and negative wires to utilise all of the heatbed pins and reduce load..
  • Silicone stranded wires for better flexibility and wear..
  • Suitable for A8 A6 3D printer heated bed..
  • Note: only hotbed line cable, no with hotbed. (If you need hotbed with line cable, please enter the ANET store for purchase).
Check Stock

Heyiarbeit 5M300 Rubber Timing Belt 5mm Pitch 20mm Width Arc Toothed Belt Synchronous Closed Loop Industrial Timing Belt for 3D Printers Black Tone

  • 【Package Included】: 10 Meters(32.8 Ft) 3D print belt with 20 teeth. Width:10mm timing belt(0.39’’).
  • 【Material】:Premium imported rubber material, which has fiberglass reinforced to be more durable and flexible..
  • 【Features】SeekLiny are professional in 3D printing accessories. The gear belt are produced by rigorous design and tested,which make it work smooth and stable.
  • mute designed & Wear-resistant with long work life..
  • 【Application】Make good performance for all DIY 3D printers,such as Creality CR10, Ender 3, Ender 5, Anet A8, E10, Anycubic, Anet series 3D printer, also suitable for most of industrial drive timing belts driven printers and so on..
  • 【5 Satrs Customer Services】Any problems about the 3d printer timing belt ,our professional team will help you solve it in the first time after you contact us..
Check Stock

Lenink Micro SD to SD Card Extension Cable Adapter Flexible Extender SD/RS-MMC/SDHC/MMC Memory Card Reader 32GB Compatible with GPS, Anet A8 3D Printer, Raspberry Pi, TV, DVD (18.9in/48cm)

  • Wide Compatibility: Micro SD to SD card extension cable compatible with Car DVD, car GPS navigation, DVR, LED/LCD screen, smartphone and 3D printers such as CR-10,Ender 3,Ender 5, Anet A8, Anet A6.
  • Fast Reading Speed: SD card extender can transfer data quickly to the card jack of most machines, read and write speed will not affect or lose any information.
  • High Quality: The 48 cm Micro SD to SD card adapter is made of plastic and FFC, which is not easy to break. Flexible and lightweight design is ideal for carrying, whether at home, on the go or at work.
  • Support: All need to use a memory card SD / RS-MMC / SDHC / MMC products. Support the card 32G, making navigation upgrade more convenient.
  • Easy to Use: Insert the SD card into the extension cable adapter, then insert the extension cable adapter into the machine, there will be a small "click" for good connection. 180 days super long warranty.
Check Stock

LANMU Micro SD to SD Card Male to Female Extension Cable Adapter, Flexible Extender Compatible with Ender 3 Pro/Ender 3/Ender 3 V2/Ender 5/Monoprice Mini/Anet A8 3D Printer/Raspberry Pi (5.9in/15cm)

  • Premium Materials: Micro SD to SD Card Extension Cable is made of High-quality Plastic & FFC.5.9in length design make it flexible and long enough to extend and read your SD cards..
  • Type: Micro SD to SD Card male to female Extension Adapter..
  • Support the card 32G, easily make your navigation upgraded, much more convenient for your life..
  • Universal Compatibility: Widely compatible with GPS, DVD, DVR, LED/LCD screen, mobile phones, Raspberry Pi and reality 3D printers, such as CR-10,Ender 3 Pro,Ender 3,Ender 3 V2,Ender 5,Anet A8,Anet A6, MonoPrice and more.(Note:If the micro sd end is locked, it will make a "click" sound to remind you. Please check it before printing.If you wanna change the card, please firstly unplug the micro sd card, change the new card,then plug the micro sd card to the printer slot again.).
  • Fast Reading Speed: LANMU SD Card Extension never affect the read and write speed of your machine, keeping it efficient and safe..
Check Stock

LANMU Micro SD to Micro SD Card Extension Cable Adapter Flexible Extender Compatible with Ender 3 Pro/Ender 3/Ender 3 V2/Ender 5 Plus/Ender 5 Pro/ CR-10S Pro /Raspberry Pi(5.9in/15cm)

  • Extended function - 15cm cable length.You can extend the card slot out of computer desk or car navigation to the place which is easy to use..
  • Switch function - TF to TF cables to extend your card reader. Let Upgrade navigation map card and music more convenient. You are deserve to have!.
  • Compatibility - Work with Ender 3/Ender 3 Pro/Ender 3 V2//Ender 5 Plus/Ender 5 Pro/CR-10S Pro/ CR-6 SE/SanDisk microSDHC / SanDisk SDXC / Raspberry Pi / Arduino /Anet A8 3D/Anet ET5 / GPS / DVD / DVR / LED / LCD screen or Smartphone etc..
  • Caution - 1.When you change another TF card, please unplug the micro sd end from device at first, and then insert it into the printer slot again. Or please pay attention to restart the device once, if you do not want to remove the other end of the extension cord from the inside of the device.2.If the micro sd end is locked, it will make a "click" sound,please check it before printing..
  • Professional Service - Provided 180 days no reason to return service. This must be the one you are looking for..
Check Stock