Reviews Adafruit Gps Module Arduino

Adafruit ItsyBitsy M4 Express Featuring ATSAMD51

  • The Adafruit ATWINC1500 WiFi Breakout uses SPI to communicate, so with about 6 wires, you can get your wired up and ready to go. Right now the Atmel-supplied library works great with Arduino M0's and M4s but does not work on Uno (328P) and may not work on other Arduinos. You can clock it as fast as 12MHz for speedy, reliable packet streaming. And scanning/connecting to networks is very fast, a few seconds..
  • This module works with 802.11b, g, or n networks & supports WEP, WPA and WPA2 encryption. You can use it in Soft AP mode to create an ad-hoc network. For secure client connections, there is TLS 1.2 support in firmware 19.4.4!.
  • Since this is our new favoritest SPI-protocol WiFi module we've decided to make a little breakout for it. The breakout comes with level shifting on all the input pins so you can use it with 3V or 5V logic. A 3.3V voltage regulator that can handle the 300mA spikes lets you power from 3-5.5VDC..
  • There's also 3 LEDs that you can control over the SPI interface (part of the library code) or you can have controlled by the Arduino library. They'll light up when connected to an SSID, or transmitting data..
Check Stock

Comimark 1Pcs GY NEO 6MV2 GPS Module NEO-6M GY-NEO 6MV2 Board with Antenna for Arduino New

  • This is GY NEO 6MV2 GPS Module NEO-6M GY-NEO6MV2 Board with Antenna for Arduino New，The default baud rate: 9600..
  • Non-brand New Chip, but the use of the same effect.，Module with antenna, mini size with strong signal..
  • EPROM save the configuration parameter data when power down，With data backup，With LED signal lights，Compatible with various flight control....
  • Package Included:1Pcs GY NEO 6MV2 GPS Module NEO-6M GY-NEO6MV2 Board with Antenna for Arduino New(If the number of products received is incorrect,....
  • We highly appreciate all customers opinions to improve the selling, also if anything you unsatisfied, please contact us for probable best solution..
Check Stock

Arduino MKR GPS Shield [ASX00017]

  • A plug 'n' play shield for experimenting with monitoring fleets, high-altitude measurements, or any kind of project requiring localization of devices..
  • Arduino MKR GPS Shield uses the u-blox SAM-M8Q GNSS (Global Navigation Satellite System) module. It is meant to be used on top of boards in the Arduino MKR boards, but thanks to its Eslov connector, it is also possible to hook it up to any board..
  • It comes with a dedicated library that allows two different interfaces and offers a consistent set of APIs designed for a full usage of the GPS acquired information..
  • Operating voltage is 3.3V, but this shield comes also with an on-board holder for CR1216 batteries..
  • The MKR GPS Shield has an additional connector meant as an extension of the I2C bus. The extra I2C port, also referred to as the Eslov self-identification port comes with: SDA, SCL, GND, +5V, and an extra digital pin, meant to send an alarm to the otherwise plain I2C devices connected to it..
Check Stock

GY-NEO6MV2 New NEO-6M GPS Module NEO6MV2 with Flight Control EEPROM MWC APM2.5 Large Antenna for Arduino Color Antenna

  • GPS modules NEO-6M,3V-5V power supply Universa.
  • GPS Module with Flight Control EEPROM MWC APM2.5 Large Antenna for Arduino.
  • Module size 25mm*35mm,Antenna size 25*25mm.
  • Compatible with various flight control modules that provide GPS computer test software.
Check Stock

Circuit Playground Classic

  • Important Note: This is the CLASSIC version of Circuit Playground. Adafruit part number 3000. The newer Express version is Adafruit Part number 3333.
  • ATmega32u4 Processor, running at 3.3V and 8MHz. MicroUSB port for programming and debugging with Arduino IDE.
  • The Circuit Playground has USB HID support, so it can act like a mouse or keyboard and attach directly to computers..
  • Green "ON" LED so you know its powered, Red "#13" LED for basic blinking.
Check Stock

Ingcool 4G/3G/GNSS HAT Module for Raspberry Pi 4B/3B+/3B/2B/Zero/Zero W/Zero WH,Jetson Nano, Based on SIM7600A-H, 4G/GNSS Module Support LTE CAT4 up to 150Mbps for Data Transfer, etc.

  • SIM7600A-H 4G HAT is a 4G/3G communication and GNSS positioning module, supports LTE CAT4 up to 150Mbps for downlink data transfer. it is pretty low power consumption.
  • Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi 4B/3B+/3B/2B/Zero/Zero W/Zero WH series boards, Compatible with Jetson Nano, SIM7600A-H 4G module control pins can connect with host boards like Arduino/STM32.
  • Supports dial-up, telephone call, SMS, mail, TCP, UDP, DTMF, HTTP, FTP, etc. Supports GPS, BeiDou, Glonass, LBS base station positioning.
  • Connect the 4G module with computer to surf the Internet, or attach it onto Raspberry Pi to enable functions like 4G high speed connection, wireless communication, making telephone call, sending SMS, global positioning, etc..
  • Comes with development resources and manual (examples for Raspberry Pi/Jetson Nano/Arduino/STM32).
Check Stock

Micro SD SPI or SDIO Card Breakout Board - 3V ONLY! Adafruit 4682

  • -165 dBm sensitivity, 10 Hz updates, 66 channels.
  • Low power module - only 20mA current draw, half of most GPS's.
  • For use with Arduino Uno/Duemilanove/Diecimila/Leonardo.
Check Stock

1.3\ TFT LCD Display HD IPS 65K 240 * 240 3.3V with SPI Interface ST7789 IC Driver, 51 STM32 Ar for Arduino Routines

  • User Manual:Adafruit_GFX:https://www.arduinolibraries.info/libraries/adafruit-gfx-library.
  • Adafruit ST7789:https://www.arduinolibraries.info/libraries/adafruit-st7735-and-st7789-library.
  • 1.3 inches colorful display lcd screen:This display is a thin film transistor type liquid crystal display and is true "Thin Film Transistor" (TFT).
  • Dot Size: 240*240 ( There are two display way: horizontal display and vertical display, you can adjust the display direction).
  • We have always cared about the customer experience and improve the product function details.
Check Stock

REXQualis Complete Starter Kit Compatible with Arduino IDE and Electronics Component Fun Kit

  • REXQualis complete starter kit base on Arduino UNO R3 comes with more than 200pcs components, 67 kinds of components and sensors module..
  • Include High Quality Base Board base on Arduino UNO R3 and Sensors, 100% compatible with Arduino IDE..
  • LCD1602 Module，MPU-6050 Module and RC522 RFID Module come with pin header, Motors come with wires, not need to solder by yourself..
  • REXQualis Electronics Component Fun Kit is a Highest Cost Components Kit, It comes with more than 400pcs sensors and components for fun and simple electronic projects..
  • Datasheet and Tutorial are available to download from our official website or you can contact our customer service..
Check Stock

REXQualis Most Complete Starter Kit Base on Arduino MEGA 2560 w/Detailed Tutorial Compatible with Arduino IDE

  • REXQualis complete starter kit base on Arduino MEGA 2560 comes with more than 200pcs components, 67 kinds of components and sensors module..
  • LCD1602 Module，MPU-6050 Module and RC522 RFID Module come with pin header, Motors come with wires, not need to solder by yourself..
  • Include High Quality Base Board base on Arduino MEGA 2560 100% compatible with Arduino IED..
  • Free PDF Tutorial and Datasheet are available to download from our official website or you can contact our customer service..
  • All of the Components and Integrated Circuits are individually packaged and labeled, and packing in a plastic box which is bigger enough for you..
Check Stock

DFPlayer - A Mini MP3 Player

  • The DFPlayer Mini MP3 Player For Arduino is a small and low price MP3 module with an simplified output directly to the speaker..
  • It supports common audio formats such as MP3, WAV and WMA..
  • The module can be used as a stand alone module with attached battery, speaker and push buttons or used in combination with an Arduino UNO or any other....
Check Stock

KEYESTUDIO MEGA Sensor Shield V1 for Arduino MEGA R3 2560 Prototype Board Projects

  • Nice Sensor shield of MEGA Rev3, Easy prototyping and Very convenient especially for 3PIN (G V S) connections. There are tons of ground and VCC headers making really it easy to connect various Arduino modules and sensors with DuPont style cables..
  • This sensor shield board really simplify the circuit and easily connect commonly used sensors.The board is having digital and analog interface, Bluetooth module communication interface, SD Card module communication interface, APC 220 radio frequency module interface, etc..
  • This sensor shield allows ease development and prototyping and makes convenient way to connect many external devices/sensors..
  • This board works well for prototyping or certain permanent applications and a very handy companion to an Mega Rev3 or compatible board..
  • 100% Compatible with the programming software for Arduino. Excellent shield board in good quality and packaged in a nice box! Great for all kinds of scientific experiment research for Arduino.
Check Stock

Screw Terminal Block Breakout Shield Module for Arduino UNO R3

  • Terminal Block Breakout Shield Module - for Arduino UNO R3. the item has been soldered and assembled..
  • Terminal block pitch 3.5mm/0.138", wire size range 26AWG to 16AWG, strip length 5mm, screw M2 steel, pin header and cage copper..
  • Standard IDC40 pitch 0.1" header, you can use 40pin FRC(flat ribbon cable) connector cable connect all Arduino Uno pins to peripheral equipment..
  • With power on LED indicating. red reset button on the side. with a ICSP adapter connect header. FR-4 fiber glass PCB, dual copper layers..
  • NOTE: the item not include Arduino Uno module..
Check Stock