Reviews Ac dc Current Sensor
UMLIFE 3pcs ACS712 Hall Effect Current Sensor Module 30A Range ACS712 Module + 3pcs Voltage Sensor Module DC0-25V Voltage Tester Terminal Sensor for Arduino Raspberry Pi
- ❃❃ Package Included:3 x ACS712 Hall Effect Current Sensor Module + 3x Voltage Sensor Module DC0-25V Voltage Tester Terminal Sensor.
- ❃❃A wide range of applications:The current sensor ACS712 provides economical and accurate solutions for ac or dc sensing in industrial, commercial and communication systems. Typical applications include motor control, load detection and management, switching power supply and overcurrent fault protection..
- ❃❃ACS712 Hall Effect Current Sensor Module:Chip: ACS712ELC-30A.
- Pin 5V power supply, on-board power indicator.
- ❃❃Voltage Sensor Module:Voltage input range: DC0-25V.
- input : Terminal cathode connected to VCC, GND negative pole.
- Output interface: "+" then 5/3.3V, "-" then GND, "s" then the for AD pins..
- ❃❃Perfect Combination:Using this product can measure both voltage and current, very suitable for DIY electronic design projects..
Check StockEast Tester Benchtop Multimeter ET1240 4-1/2 Digit Digital Multimeter Voltage Tester
- Using 3.5 inch TFT LCD display (resolution 320*480), the brightness of the screen can be adjusted. Language switching between Chinese and English. Two-parameter display can display two parameters of the same input signal..
- Overrange display: 120% of range. Measurement of AC/DC Voltage, AC/DC Current and 2/4 Line Resistance. The maximum DC current is 10A and the maximum DC voltage is 1000V. External calibration function to support user self-calibration..
- Periodic and frequency measurements, maximum frequency 20 MHZ. Capacitance measurement, maximum 10 mF. True RMS AC voltage and AC current measurements, bandwidth up to 100 kHz..
- Optional manual or automatic range. Ten Mathematical Functions: MX+B, MAX, MIN, Average, dB, dBm, REL, Hold, Limit Comparison, Statistics. Supporting a variety of sensors: 10 thermocouples, 4 thermal resistors..
- Built-in temperature sensor for cold-end compensation, support automatic and manual compensation. Data Memory Storage and Reading Function for Easy Viewing of Data Information. Supporting SCPI protocol and providing programming documentation..
Check Stockuxcell 5pcs ZP4510 Liquid Water Level Sensor Vertical Float Switches
- Switch Body Size : 23.3 x 57.7mm / 0.9" x 2.27"(Max D*H).
- Package Content : 5 x Water Level Sensor.
Check StockSiglent Technologies SDM3065X 6 ½ Digit Digital Multimeter, DMM
- Real 6½ digits readings resolution (2,200,000 counts).
- Comes with easy,convenient and flexible any sensor measurement control software: EasyDMM.
- Standard interfaces: USB Device, USB Host, LAN (Optional Accessories: USB-GPIB Adapter).
- DC Voltage: 200 mV - 1000 V, DC Current: 200 μA - 10 A, AC Voltage: True-RMS, 200 mV - 750 V, AC Current: True-RMS, 200 μA - 10 A..
Check Stockuxcell BWL100 100 mm Pull Rod Linear Position Displacement Sensor for Printer
- Shipping list: AC 220V vibration sensor delay module, with ultra-high sensitivity vibration sensor..
- AC 220V power supply ultra-high sensitivity vibration delay module plus relay module plus delay three-in-one module, vibration switch module Alarm trigger, with 1 vibration sensor. Relay does not have B1 normally closed end..
- corridor delay switch, delay energy-saving products.
- Supply voltage: AC 220V power supply, Current: greater than 100mA.
Check StockCurrent Sensing Relay AC Current Sensing Switch 0-50A Normally Closed Current Sensor Monitoring Relay NC50
- Universal Outputs: Input through current: 0.2-50A AC Rated load: [email protected] AC/DC..
- Accurate & Dependable: Offers a sensing range of 0.2 to 50 amps and universal, solid-state outputs.
- Faster Response Time: Once current flow is detected, it closes a set of contacts immidiately.
- Self-powered, no external power supply required,adjustable with a potentiometer.LED indicator can conveniently and intuitively indicate the working status of the switch..
- Normally Closed current sensor:Suitable for AC current measurement and monitoring, AC motor overload protection, electronic switch of automatic control system and so on..
Check StockSparkFun (PID 14544 Current Sensor Breakout - ACS723 (Low Current)
- ACS723 AC DC current sensor with OPA344 OpAmp.
- Measure both AC and DC currents from 10mA up to 5A.
- Capable of 80KHz bandwidth. Fixed to 20KHz on board. JP1 can be closed to enable all 80KHz.
Check StockINA219 High Side DC Current Sensor Breakout - 26V ±3.2A Max
- 【Mini Split Base Current Transformer】It's the smallest one compared to the similar products (output 100MA).Current Transformer, 100A 100mA AC Current Sensor, Split Core Amp Transformer Sensing Relay, Mini Clip-on Easy to Install CT Without Power Off. current sensor structure sensor.
- 【Professional Use】Current transducer used for energy meter in special.
- AC 220v, 380v power supply can both be applied.plit Core Current Transformer,AC Current Sensor,Output Class Analog Sensor,Working Principle Magnetic Sensor, Useful for Measuring Whole Building Electricity Consumption.current sensing relay isolation.
- 【Good Mechanical Properties】Fully enclosed, good mechanical properties and environmental resistance, strong voltage isolation capability, safety and reliability..
- 【Snap Joint Structure】The diameter of inner hole is 16mm, the accuracy is 0.5 grade, Using snap joint structure, it can be fixed to the cable directly through nylon ties..
- 【Easy to use】When you fix the energy meter, you don't need to cut off the power if you use this product. Split Core Current Transformer Coil Sensor for 100A Amp Energy Meter.ac transformer amp meter amp tester.
Check StockFluke 325 Clamp Multimeter AC-DC TRMS
- Digital clamp meter measures AC current to 400 amp, AC and DC voltage to 600V, and resistance to 4 kilohms.
- True RMS sensing meter provides accurate readings when measuring linear or non-linear loads, regardless of waveform.
- Jaw opening measures current in a conductor up to 30mm without touching or interrupting the circuit.
- Audible continuity sensor confirms that the circuit conducts electricity.
- Meets IEC safety standard 61010-1, and is rated for CAT IV installations to 300V and CAT III installations to 600V.
Check StockBTMETER AC/DC 1000A Clamp Multimeter, 4000 Counts Digital Clamp-on Meter with Data Logging Measure Amp Volt Ohm Capacitance Frequency Temperature Continuity, Electrical Tester 570T-APP
- ⚡【DC AC Current Clamp Multimeter】This multifuctional clamp-on meter can accurately measures AC DC current with 400A/1000A ranges, 100mA/1A resolution;AC and DC Voltage to 1000V, Resistance to 60M ohms.
- Temperarture -4~1832℉ (℃/℉ Optional), Test voltage 4V, can measure light-emitting diodes, and continuity test..
- ⚡【Sensitive Hall Effect Clamp Sensor】Engineered with hall effect sensor to ensure high precision measurement on DC/AC amperage testing. Built with big jaw caliber size 1.77 inches (45mm), allows you non-contact measuring multiple wires at the same time. ❗Please separate the hot and neutral conductors or they will cancel each other out and give zero amp reading, just clamp on the LIVE line for accurate amperage testing❗.
- ⚡【Electrical Data Logger】Get rid of hand-written notes or complicated maths. With this intelligent clamp amp meter, all electric measurements will be displayed on your phone or tablet, auto graph a trend chart, support to sharing out in Excel, TXT format. This clamp-on ammeter is reliable on remotely troubleshoot electrical problems in HVAC, household, commercial,....
Check StockBTMETER BT-90EPC Digital Multimeter, Auto-Ranging AC/DC Volt Amp Ohm Temperature Electric Multi-Tester, w/ USB to PC Link Sync for Data Logging
- 【Datalogging Digital Multimeter】This voltmeter can connect with a computer via USB cable using the software included in the CD Allows you to monitor & log the voltage, current, temp, resistance etc. Display all measurement on the same interface including: Max/min/current, on-screen graphing, real-time clock, sampling rate setting, export data to Excel/TXT file.
- 【Multifunctional PC Link DMM】Data-recording multi-meter measures AC/DC Voltage, AC/DC Current, resistance, frequency, capacitance, temperature, diode test, continuity buzzer, 1.5V/9V battery test..
- 【Auto-Backlight & Auto Shutdown】Built with a light sensor to sense the ambient brigtness, turn ON/OFF backlit screen automatically, no more pressing a button back on forth during the measurement. In case you forget to turn the meter OFF, it’ll auto power OFF after 30 mins of operation. Long press “SELECT” you can disable it anytime..
- 【Attached to Clamp-on Amp Probe】It’s more convenient to attach the BT-90EPC meter to BT-605A AC/DC Amp Clamp Probe for amps measurement. Allowing you remotely monitor to computer and record the circuit data..
Check StockDollaTek 5Pcs SW-420 NC Type Vibration Sensor Module Vibration Switch
- Shipping list: 1 channel 24V vibration sensor plus relay module with 1 meter long shock sensor.
- 6-24V wide voltage power supply stable version With 1 meter long vibration sensor module, this module has no vibration delay function..
Check StockFluke 324 True RMS Clamp Meter
- Digital clamp meter measures ac current to 400 amp, ac and dc voltage to 600v, and resistance to 4 kilohms.
- True RMS sensing meter provides accurate readings when measuring linear or non linear loads, regardless of waveform.
- Jaw opening measures current in a conductor upto 30 millimeter without touching or interrupting the circuit.
- Audible continuity sensor confirms that the circuit conducts electricity.
- Meets IEC safety standard 61010 1, and is rated for CAT IV installations to 300V and CAT III installations to 600V.
- CAT IV 300V/CAT III 600 Volt safety rating.
Check Stock