Reviews 51threaded Tank

Class A Customs | Under Mount 30 Gallon RV Concession Fresh and Gray Water Holding Tank & Plumbing Kit | UM-3000-BPK

  • ...view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and water-tight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT Over-tighten fitting damage will occur – Use plastic threaded fittings, metal threads may damage tank fittings.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES: (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” ID Vent/Draw Hose (ONE) 5ft. Section of 1.25” ID (1.375” OD) Fill Hose.
Check Stock

Atima Generator Accessories – Extended Run Dual Fuel System Extender Kit for Honda Generator

  • ...ge]:1: Run honda generator fuel extender System Each fuel pipe interface is a quick interface, so it is very convenient to connect .2: When using our products, the generator ,fuel tank and leather pipe are directly connected, not twisted, reducing the distortion of the leather tube and increasing the service life..
  • [Thread fit] :The fuel tank cap thread is tightly coupled with the generator thread, and the rubber gasket is squeezed with the generator port to form a seal to prevent air from entering..
  • [Tips]：The users should buy another tank with Thread outlet to connect this system , like attwood 8806LPG2S Epa Certified Portable Fuel Tank.The model number of the generator must match the model of the fuel cap.In use, as for the users except Honda generator users, the tank should be placed at a higher position than the generator, using gravity to transport oil.Carefully rotate the fuel tank cap on the generator to prevent damage to the plastic thread on the fuel tank..
Check Stock

Class A Customs 13 Gallon Water Tank & Plumbing Kit T-1300-BPK

  • ...g process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adapter (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adapter (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adapter (ONE) 5ft. Section of 0.5” ID Vent/Draw Hose (ONE) 5ft. Section of 1.25” ID (1.375” OD) Fill Hose.
Check Stock

Class A Customs | 30 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-3000-BPK-PUMP

  • ...y Water Storage ||WATER TANK MEASUREMENTS: 34 1/2” Longest Length (not including fittings) x 12” x 17 1/2” (rotate tank to change height or width) Average thickness 7/32” +/- (+/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Balloon Style Threaded Female NPT Standard - fitting will be closed, to use remove inner membrane with razor knife (TWO) .5" Threaded Female NPT Standard - open fitting, unsealed.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT hook garden hose directly to tank doing so will cause tank to explode resulting in damage..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” ID Vent/Draw Hose (ONE) 5ft. Section of 1.25” ID (1.375” OD) Fill Hose.
  • classAcustoms 12 VOLT FRESH WATER PUMP | on demand diaphragm pump | MODEL # 12V3 - READ INCLUDED INSTRUCTIONS BEFORE INSTALLATI....
Check Stock

275-330 Gallon IBC Tote Water Tank Adapter 2' Coarse Thread + Lead Free Brass Hose Faucet Water Shut-Off Valve with Ball Valve, IBC Water Tank Fitting, Garden Hose Connector Replace Valve Parts

  • 【2” COARSE THREAD】This is an 2″ coarse thread IBC tank adapter with brass faucet spigot and detachable faucet connector. The interface of IBC tote adapter is coarse thread with outside Diameter: 60mm (2.36″), and the thread pitch is 6mm (0.24″). The Brass Garden Hose Ball Valve/Faucet interface is 1/2″, It can be directly connected to garden pipe fittings, no need additional brass adapters to fit your garden hose. Please confirm the thread diameter of your IBC tank adapter is 60mm..
  • 【PREMIUM QUALITY】The Tank Adapter is made of high quality Lead free Copper and PE. It can be Anti-corrosion, acid, alkali resistance and durable. The IBC tote tank Water Drain Adapter is suitable for drinking water and applications of food-grade. It can be used to store beer, it also can be used in a tank containing a chemical or other liquids..
  • 【REPLACEMENT TON BARRELS FAUCET】Replace the new water tank adapter in time to protect the life of your existing valve or for fine flow control. This is a good way to stop beating the knuckles on the tank cage and allows you to draw water off a tank with ease, the tap also acts as useful back up safety valve..
  • 【SAVES TIME AND LEAKPROOF】It fits most standard UK and European IBC containers where the buttre....
Check Stock

IBC Tote Adapter: 2in Buttress to 2in NPT Pipe Thread - Easily Connect Your IBC Tote to Standard Pipe Thread - Buttress Adapter - IBC Tote Valve - Food Grade Tote - IBC Tote Fittings - Food Grade Drum

  • 【2” COARSE THREAD】This is an 2″ coarse thread IBC tank adapter with brass faucet spigot and detachable faucet connector. The interface of IBC tote adapter is coarse thread with outside Diameter: 60mm (2.36″), and the thread pitch is 6mm (0.24″). The Brass Garden Hose Ball Valve/Faucet interface is 1/2″, It can be directly connected to garden pipe fittings, no need additional brass adapters to fit your garden hose. Please confirm the thread diameter of your IBC tank adapter is 60mm..
  • 【PREMIUM QUALITY】The Tank Adapter is made of high quality Lead free Copper and PE. It can be Anti-corrosion, acid, alkali resistance and durable. The IBC tote tank Water Drain Adapter is suitable for drinking water and applications of food-grade. It can be used to store beer, it also can be used in a tank containing a chemical or other liquids..
  • 【REPLACEMENT TON BARRELS FAUCET】Replace the new water tank adapter in time to protect the life of your existing valve or for fine flow control. This is a good way to stop beating the knuckles on the tank cage and allows you to draw water off a tank with ease, the tap also acts as useful back up safety valve..
  • 【SAVES TIME AND LEAKPROOF】It fits most standard UK and European IBC containers where the buttre....
Check Stock

Class A Customs | T-1000-BPK| 10 Gallon Fresh Water Tank & Plumbing Kit RV Concession

  • ...g process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” ID Vent/Draw Hose (ONE) 5ft. Section of 1.25” ID (1.375” OD) Fill Hose.
Check Stock

Class A Customs | T-2100-BPK| 21 Gallon Fresh Water Tank & Plumbing Kit RV Concession

  • ...g process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” ID Vent/Draw Hose (ONE) 5ft. Section of 1.25” ID (1.375” OD) Fill Hose.
Check Stock

Class A Customs | T-4000-BPK| 40 Gallon Fresh Water Tank & Plumbing Kit RV Concession

  • ...g process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” ID Vent/Draw Hose (ONE) 5ft. Section of 1.25” ID (1.375” OD) Fill Hose.
Check Stock

Class A Customs | T-3000-BPK| 30 Gallon Fresh Water Tank & Plumbing Kit RV Concession

  • ...g process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” ID Vent/Draw Hose (ONE) 5ft. Section of 1.25” ID (1.375” OD) Fill Hose.
Check Stock

Evaty 5 Pack Aluminum Alloy Metal Stand Base Holder (Silver)

  • 1pcs Thick Acrylic stand display for 510 screw thread RDA tank, 9pcs silicon anti-slip ring , the 9pcs silicone suits for different size of tank ..
  • there are 9pcs 510 screw thread for RDA tanks , 9pcs silicone anti-slip rings (3pcs in 25mm diameter , 3pcs in 22mm diameter , 3pcs in 18mm diameter ).
  • the 9 holes are with 510 thread screw , it suits any 510 thread screw tank.
  • screw the 510 RDA tank on the stand . it will not fall off , keep your tanks all standing in order .NOT in a mess ..
Check Stock

QISF Multi-Purpose 2 Pack Screw Thread Pitch Gauge Tool, Pitch Cutting Gauge Caliper Gages Measuring Tool, 51 Pcs America SAE Type + 58 Pcs Metric & America SAE Type & British Whitworth

  • 【Function】-- 2 In 1 set Screw Thread Pitch Gauge Tool, Pitch Cutting Gauge Caliper Gages Measuring Tool.
  • 51Pcs Blade America SAE Type and 58Pcs Blade Metric & America SAE Type & British Whitworth.
  • 【Wide application】-- Accurately measures internal and external screw threads with thread blades of varied size.
  • Use to provide the correct size drill bit, or to size fastener to determine what bit should to use. Used for checking tool angle while cutting threads in metal turning lathes, accurately measures internal and external screw threads with thread blades of varied size.
  • 【Material】--Stainless steel and chrome finish, it combines high strength, good resilience, elegant appearance. Not easy to rust and long lasting durability.
  • 【Size】-- 51 Pcs America SAE Type Measuring range: 4-84.
  • / 58 Pcs Metric & America SAE Type & British Whitworth Metric:0.25-6.0 Imperial:4G-62G US: 8, 10, 11, 14, 19, 28.
  • 【Package】-- 1 x 58Pcs Blade Metric & America SAE Type & British Whitworth.
Check Stock

Class A Customs | Under Mount 20 Gallon RV Concession Fresh and Gray Water Holding Tank & Plumbing Kit UM-2000-BPK

  • ...g process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” ID Vent/Draw Hose (ONE) 5ft. Section of 1.25” ID (1.375” OD) Fill Hose.
Check Stock