Reviews 3d Printer Heater

Youyoute Mini Heater for 3D Printer, Resin 3D Printer Temperature Controller Heating Thermostat Temp Control for LCD DLP 3D Printers

  • 【Use for】Resin 3D printer mini heater designed for Resin 3D printers, it is small but powerful, for use in cold weather. It helps you to heat up the resin and rise the ambient temperature. Make your 3D printer work well, save your time and Resin material..
  • 【Professional design】Our temperature controller use in cold weather,when temperature lower than 75F/24C, will cause so many problems in LCD DLP 3D print. Such as Print not sticking to the bed, Layer adhesion, warming, and so on. Finally, printing fails..
  • 【Professional design】Our 3D printer heater built in high-precision temperature sensor, accurate to 0.1 ℃. Fireproof case, high-quality power cord, all professionally designed for your safe printing..
  • 【Small size】Our 3D printer Thermostat 10.8x5.7x3.2cm/4.25x5.24x1.25 in, 117grams, Prefect for 8-15 inch Resin 3D printer, It only takes 10 minutes from 40F to 80F, for use in cold weather..
  • 【Function】3D printer air controller contains three functions, one is heating, one is Air circulation, and the other is filtering. When the temperature is lower than the set t....
Check Stock

Ender 3 Hotend 3D Printer Extruder Assembled MK8 Hot End Kit for Ender 3/Ender 3 Pro with Aluminum Heating Block, 1.75mm, 0.4mm Nozzle

  • 100% Creality 3D original and high quality 3D printer accessories.
  • Hotend replacement parts suitable for ender 3, ender-3x, ender-3 pro 3d printer.
  • Tip of the nozzle, Aluminum Heating block, Throat Pipe (Built-in Teflon).
  • MK8 extruder hot end kit with thermistor and heater,24V 40W.
Check Stock

Ewigkeit 24V 40W Heater Cartridge 620 Ceramic Hotend for 3D Printer Prusa Mendel (Pack of 5pcs)

  • 24v cartridge Heater is made of 304 stainless steel material,Diameter: 6mm.
  • Voltage: 24v, Power: 40w, Conveniently pre-wired with 1 meter long high temperature resistant wire.
  • Easy installation, wide temperature range, good stability, high reliability provide a high corrosion prevention.
  • Heating cartridges work with Creality CR-10S Pro,CR-X,Ender 3, Ender 3X, Ender-3 Pro 3d printer,Anet E10 etc.
  • 5pcs of 24V 40W 620 ceramic cartridge heater for 3D printer hotend.
Check Stock

Wangdd22 15pc/Set 1.75mm Teflon Throat Tube+0.4mm Extruder Nozzle Print Heads+Heater Blocks Hotend for MK8 Makerbot Anet A8 3D Printer

  • Pack of 5 x 3D Printer Extruder Hotend 30mm Length 1.75mm Nozzle Inputting Tube( for MK8 Makerbot Reprap Prusa I3 3D Printer) and 5 x 3D Printer 0.4mm....
  • 0.4mm Extruder Brass Nozzle Print Head: Color - Golden.
  • Compatibility: compatible with all 1.75mm PLA ABS 3D Printer.
  • Quanlity:15pcs/lot (5 piece 1.75mm Nozzle Inputting Tube,5 piece 3D Printer 0.4mm Extruder Brass Nozzle Print Head,5 piece Heater Blocks Hotend).
Check Stock

EIBOS 3D Printer Filament Dryer Box 3D Filament Storages with Fan Keeping Filaments Dry During 3D Printing Compatible with 2 Rolls 1.75mm 2.85mm 3.00mm PLA PETG ABS Spool Holder

  • 【DRYER & STORAGE BOX】the dryer box is specifically made for the purpose of drying 3D printer filament, intended to remove the moisture from a....
  • 【ADJUSTABLE TEMPERATURE & HUMIDITY MONITOR】adjustable heating temperature to accommodate needs of various filaments, actual and setting temp are....
  • 【COMPATIBLE WITH MULTIPLE SPOOLS】filament dryer box works for different filament types and diameters, compatible with 1.75mm, 2.85mm, 3.00mm 3D....
  • 【REVIVE YOUR BRITTLE FILAMENT】filament dryer box aims at drying the wet or brittle 3D printer filament, or even make it better than the brand new....
  • 【100W PTC HEATER】Different from applying ordinary heater 48W PI heating pad to heat up space, our product use 100W PTC heater which is more....
Check Stock

Onyehn 22pcs/Lots A8&A2 3D Printer Part Each 5PCS 0.4mm Extruder Nozzle Print Head+1.75mm Teflon Throat Tube+Heater Blocks Hotend for MK8 Makerbot Reprap

  • Pack of 5 x 3D Printer Extruder Hotend 30mm Length 1.75mm Nozzle Inputting Tube( for MK8 Makerbot Reprap Prusa I3 3D Printer) and 5 x 3D Printer 0.4mm....
  • 0.4mm Extruder Brass Nozzle Print Head: Color - Golden.
  • Compatibility: compatible with all 1.75mm PLA ABS 3D Printer.
  • Quantity:22pcs/lot (5x 3D Printer Nozzle Throat Tube 5x Nozzle Print Heads 5x Heater Blocks Hotend 5x M6 nuts 2x Hex Key Wrenches (for MK8 Makerbot....
Check Stock

MK10 3D Printer Extruders Kit 5 Pcs Aluminum Heater Block + 1.75mm Extruder Throat Tube M7 Thread + Cotton Heater Tape for 3D Printer Wanhao Filament

  • ✹✹ High quality copper and stainless steel, ensure concentricity and roundness.
  • Designed for many common types of 3D printers, solid aluminium construction with aperture..
  • ✹✹ Aluminium Heater Block for Extruders in 3D-Printers. A drilling with an M4 screw is scheduled for the optimal fixing of the Cartridge Heater. The Thermistor is fixed by means of a M4 grub screw in order to avoid slipping or loosening. The heating block is equipped with an M7 thread for the Nozzle..
  • ✹✹ Compatibility: Fit with MK10 hotend aluminum cooling block, such as DIY MK10 3D printer, FlashForge Creator Pro, FlashForge Creator X, FlashForge Dreamer, Dremel Idea, Builder PowerSpec 3D, Pro PowerSpec 3D X, Wanhao Duplicator 4S, Wanhao Duplicator 4X, Wanhao i3, etc..
  • ✹✹ 2mm thick cotton heater tape for heat preservation, keep heater block and consumable work better..
  • ✹✹ Any questions, you can tell us and we will give you a satisfied solution!.
Check Stock

3D Printer Parts Accessories Tool Set Cleaner Kit 41PCS with E3D Nozzles Cleaning Needles Tweezers Heater block and Cover,Tube Throat for Ender 3 Pro/Ender 5/ CR-10/10S

  • Aluminum Heater Block: Works perfect with nozzle and nozzle throat..
  • Stainless Steel Throat: 3D printer parts aluminum heater block extruder hotend kit is replacement parts for Ender 3 /Ender 3 Pro / Ender 5 /Ender 5....
  • 0.4mm Brass Nozzles: The 3d printer nozzles can prevent print head from leakage effectively and produce consistent prints with smooth and glossy....
  • PTFE Teflon Bowden Tube : PTFE Tubing can resist higher temperature than any other tubing, which is perfect for printing exotic filaments such as ABS,....
  • Excellent Cleaning Needles: The E3D nozzle cleaning needles are very flexible and robust, easy to bend the needle into nozzle and will not break.....
Check Stock

YOTINO 10Pcs 3mm Thick Heating Block Cotton and Aluminum Heater Block for MK7 MK8 Makerbot 3D Printer Hotend Nozzle

  • 【Value Pack】5 Pcs Aluminum Heater Blocks, 10Pcs 3mm thick 3D printer heating block cottons..
  • 【Aluminum Heating Block】M6 heating block: 20 * 20 * 10mm, Inner hole for set screw: M6 and M3 (heat pipe and thermocouple)..
  • 【Heating Block Cotton】Size:20 * 70 * 3mm. Resistance to thermal shock, low thermal conductivity and thermal capacity,saving power and energy. Better printing effect with this 3d printer heat insulation cotton..
  • 【Perfect Compatibility】These heating aluminum blocks are suitable for MK7 MK8 Makerbot 3D Printer structure, works with extruder nozzle throat & heat-insulated cotton..
  • 【Note】The thermal insulation cotton does not have the pre-punched holes, you can cut to the appropriate size and punch holes on the cotton according to your need..
Check Stock

Creality CR10 Heat Bed 12V Aluminum Heat Bed with Cable and Insulation Mat Installed Well Compatible for 3D Printers Creality CR10 / CR10S Hot Bed Size 310x310x3mm

  • Upgraded 2018 Which Heating Much Faster and with 12V Voltage 18A 220W.
  • Original Parts / Accessories Replacement for Creality 3D Printer CR-10 / CR-10S.
  • Hot Bed Size:310x310x3mm，Hotbed With Cable Which be Installed Well..
  • We only guarantee our heater bed be used on the original creality 3D printer CR-10 and CR-10S.
  • if be used to the other brand modles, customers need to afford to the resonsibility by themselves, meanwhile, our warranty will not valid for this cause..
  • WARRANTY: All 3D printer accessories with 12 Months Warranty and Lifetime Technical Support..
Check Stock

MakerHawk 5pcs Aluminum Heater Block for MK7 / MK8 3D Printer and 5pcs NTC 3950 100K Thermistor with 1 Meter Wiring and 5pcs 12V 40W 620 Ceramic Cartridge Heater for 3D Printer

  • 3d printer heater block: Inner hole for set screw: M6 and M3 (heat pipe and thermocouple)..
  • 12V 40W 620 Ceramic Cartridge Heater: Resistance: Material: 304 stainless steel.
  • 2080 high temperature resistant high quality....
  • NTC 3950 100K Thermistor: For 3D printers: use TEMP_SENSOR 11 in Marlin firmware.
  • Cartridge Heater: The solids, liquids, and gases need to be heated by cartridge heater, transmit heat quickly by conduction if the producer of the....
  • We have a strong after-sales team, if you have any questions, please feel free to email us. Click on "MakerHawk-US",then "Ask a question".We will....
Check Stock

ChowThink High Temperature Fast Heating E3D V6 Hot End Full Kit 3D Printer Extruder Parts Accessories Parts

  • Well-made: Copper Chrome-plated Heater Block, good thermal conductivity, high temperature resistance，Hollow design, fast heat dissipation.
  • Compatible with all 1.75mm E3D V6 Makerbot 3D Printer，Easy to install, With installation tool ..
  • Easy to install Upgrade the all metal hotend to effectively solve the problem of leakage and blockage during the printing process..
  • Kit Includes: Aluminum Cooling Block, Grade 5 Titanium Heat Break, Copper chrome-plated Heater Block, Copper chrome-plated Wear Resistant MK8 0.4mm....
  • Made by ChowThink，Any Questions contact us freely..
Check Stock

ExcelFu 5pcs 30MM Length Extruder 1.75MM Teflon Throat Tube and 5pcs 0.4MM Brass Extruder Nozzle and 5pcs Heater Blocks Hotend for MK8 Makerbot Anet A8 3D Printer (Bonus: 2pcs hex Key Wrenches)

  • 5x 3D Printer Nozzle Throat Tube + 5x Nozzle Print Heads + 5x Heater Blocks Hotend + 2x Hex Key Wrenches(for MK8 Makerbot Reprap Prusa I3 3D Printer).
  • Nozzle Throat Tube: Material - Stainless Steel.
  • 0.4mm Extruder Brass Nozzle Print Head: Color - Golden.
  • Compatibility: compatible with all 1.75mm PLA ABS 3D printer, works with Anet A8.
Check Stock