Reviews 0 10v Signal Control

WSDMAVIS 2Pcs PWM to Voltage Module 0% -100% PWM Converted to 0-10V Voltage Digital Analog Signal Converter for PLC Signal Interface Switching

  • The PWM transfer voltage module LC-LM358-PWM2V converts the PWM digital signals into 0 to 10V analog signals.Allowable error:5%..
  • It can be used as signal interface switching for PLC or other industrial control boards. The output voltage is regulated by adjusting the duty ratio of the PWM..
  • The modules are small in size and easy to use in different places.Easy to operate, fine tuned by potentiometer..
  • MCU embedded technology.Work Voltage:DC 12V-30V(Power requirements:> 100MA).
  • Select the PWM signal input level range through short-circuit.The peak of 4.5V to 10V level. The short cap install in ‘5V’. This level is used for normal controller or 5V MCU.
  • The peak of 12V to 24V level, so inserted in 24V. The short cap install in ‘24V’. This level is used for normal PLC controller..
Check Stock

PC Interface Controller

  • 【One-year after-sale warranty】The PWM to voltage module converts PWM digital signals to 0 to 10V analog signals. It can be used to switch the signal interface of PLC or other industrial control board. Adjust the output voltage by adjusting the PWM duty cycle. The module is small in size and easy to apply in different places.003cbr003e.
  • Using MCU embedded technology. Easy to operate, can be fine-tuned by potentiometer.003cbr003e.
  • Select the PWM signal input level range by short circuit. The module is small, easy to carry and easy to use.003cbr003e.
  • (current greater than 100mA),PWM signal receiving frequency range: 1KHZ-3KHZ.
  • When power on for the first time, it is best to do a calibration and debugging: find a signal with a 50% duty cycle and connect it to PWM and GND. Jumper caps set the corresponding voltage range. When the frequency is 1KHZ-3KHZ, use a multimeter to measure the two ports of VOUT and GND. At this time, the meter displays about 5V. Adjust the potentiometer on the board so that the multimeter displays 5.00v.003cbr003e.
Check Stock

AudioPipe APTV-600.4 Full Range IP67 Waterproof Marine Bridgeable Class D Amplifier for ATVs, UTVs, Boats, and Motorcycles, Black

  • CLASS D WATERPROOF AMPLIFIER: Bridgable class D amplifier ideal for side-by-sides, UTV's, ATV's, boats, or motorcycles.
  • RMS POWER SPECS: Output power (RMS): 60 watts x 4 channels at 4 ohms.
  • MULTIPLE PROTECTIONS: Thermal, over current, and short circuit protection ensure your equipment is safe and secure.
  • LOW RESISTANCE TECHNOLOGY: Features surface mount technology (SMD) with a 4 layer fiberglass printed circuit board (PCB) design.
  • AMPLIFIER SPECIFICATIONS: Adjustable HP/LP frequency control.
  • Frequency response: (-3dB) 20Hz to 20KHz.
Check Stock

ZZLZX DC 0/1-10V LED Dimmer Knob Controller Rotary Mini Switch LED Light Controller Lighting Spotlight Grow Lamp LED Driver

  • Durable material: the dimming knob controller is made of durable plastic and metal, with exquisite technology and heat resistance, and is not easy to damage, and can be reused for a long time..
  • The interface must have a voltage of 10V for dimming.
  • The maximum load of the connected driver is 10V / 40mA.
  • The minimum output connecting cable size is 1007#20awg.
  • Easy to use: the dimmer adopts knob control. You can adjust the brightness by rotating the knob to realize stepless dimming. The knob operation design can adjust the light to the appropriate brightness according to the actual demand, which is easy to operate..
  • Package includes: 1 dimming knob controller.
  • The wiring is simple and convenient. Keep the driver away from the direct heat source and well ventilated space. If there is a built-in driver, sufficient ventilation must be ensured..
  • Widely used: it is applicable to all 0-10V electrical adjustment, plant lamp dimming, down lamp, track lamp, wall washing lamp, LED lamp, etc.
  • Tunable optoelectronic LED drivers and ballasts, transformers and power dimmers..
Check Stock

35A Electronic Speed Controller 3~6S Brushless ESC AM_32bit RC Controller Compatible for RC Crawler Truck & RC Car Model

  • The continuous current of 35A ESC is 35A, and the instantaneous peak can be up to 40A(≤10S). The working voltage is DC10V to 25.2V.
  • Electronic speed controller is supported DShot150/ 300/ 600/ 1200/ Oneshot/ Multishot and PWM, specializing used in RC car models, such as RC crawlers, trucks, cars. Please note, this ESC only can use for RC car models.
  • The input voltage is suitable for a 3~6s lipo battery. It is optimized for RC outrunner motors, suitable for EVO series motors and other outrunner motors, which can have well-used in RC car models.
  • The throttle signal cable is twisted pair, which is more effective, long life, and reduces interference, making the flight more stable.
  • The size of 35A ESC controller is 1.26 x 0.63 x 0.24in (32 x 16 x 6mm) and the weight is 8.1g(Including wires). The package included one electronic speed controller.
Check Stock

Agatige Frequency to Voltage Converter Module, 0-10Khz to 0-10V F/V Digital to Analog Converter Conversion Module

  • FUNCTION: The frequency of the pulse signal 0HZ to 10KHZ converts into an analog voltage signal of 0-10V. Can be used to interface switching between the PLC and the frequency converter, or interface matching such as the matching of motion control card and inverter control..
  • FEATURES: Input pulse level is 5V 12V 24V, which can be directly entered without serial resistor. The input signal frequency must maintain more than 0.5 seconds..
  • ANTI-INTERFERENCE: Conversion module's signal inputs with optical coupling isolation, which can ensure that the capability of anti-interfence..
  • APPLICATION: Frequency to Voltage Converter Module Can be used for industrial control panel PLC or other signal interface switching.
  • MAJOR SPECIFICATIONS: Output current: 5MA,Voltage: 0-10V, Input pulse level: 5V 12V 24V, Frequency: 0 to 10KHZ..
Check Stock

UpBright 9V AC/DC Adapter Compatible with Nintendo SNS-002 SNS002 Super NES Control Deck SNS-001 SNS001 SNES Mini DC10V 850mA 10V 10VDC 10.0V 0.85A 10 V Class 2 Power Supply Cord Charger Mains PSU

  • World Wide Input Voltage 100-240VAC 50/60Hz. OVP, OCP, SCP Protection (OVP: Over Voltage output Protection. OCP: Over Current output Protection. SCP: Short Circuit output Protection). Tested Units. In Great Working Condition. UpBright 30 days money back guarantee. 1 full year service warranty..
  • UpBright New Global 9V AC / DC Adapter Compatible with Nintendo SNS-002 SNS002 Super NES Control Deck SNS-001 SNS001 SNES Mini DC10V 850mA 10V 10VDC 10.0V 0.85A 10 V 10.0 VDC 9V - 12V Class 2 Power Supply Cord Cable PS Wall Home Battery Charger Mains PSU (Come with a Smart Plug Tip pigtail for greater compatibility.).
Check Stock

10-50V 100A 5000W DC Motor Engine Speed Controller 0-100% PWM Control Industrial Motor Speed Regulator for DC Brush Motor DC Lamps

  • PWM Duty Cycle:0%-100% and Quiescent current is 0.04A( not over 40mA when voltage is DC10V to DC30V).
  • Operating temperature:-20 to 40.It can perform normally when the temperature is below 0.
  • Universal speed controller can be used for DC brush motor, suitable for car cooling fan motor, car air conditioning motor, exhaust blower, treadmill motor, etc.
  • This motor speed controller can also be used for dimming DC lamps or controlling DC heater.
Check Stock

Juried Engineering CD4016BE CD4016 4016 100-pA 20-V 1 1 SPST 4-Channel Analog Switch Breadboard-Friendly IC DIP-14 Pack of 10

  • 20-V digital or ± 10-V peak-to-peak switching.
  • 280 ohm- typical on-state resistance for 15-V operation, Matched control-input to signal-output capacitance: Reduces output signal transients, Frequency response, switch on = 40MHz (typ.), Maximum control input current of 1 µA at 18 V over full package temperature range.
  • Switch on-state resistance matched to within 10 ohm typ. over 15-V signal-input range, High on/off output-voltage ratio: 65 dB typ. @ fis = 10 kHz, RL = 10 k ohm, Low crosstalk between switches: –50 dB typ. @ fis= 0.9 MHz, RL = 1 k ohm, 5-V, 10-V, and 15-V parametric ratings.
  • Example Applications: Analog signal switching/multiplexing: Signal gating, Squelch control, Chopper, Modulator, Demodulator, Commutating switch, Digital signal switching/multiplexing, CMOS logic implementation, Analog-to-digital & digital-to-analog....
Check Stock

Juried Engineering CD4016BE CD4016 4016 100-pA 20-V 1 1 SPST 4-Channel Analog Switch Breadboard-Friendly IC DIP-14 Pack of 20

  • 20-V digital or ± 10-V peak-to-peak switching.
  • 280 ohm- typical on-state resistance for 15-V operation, Matched control-input to signal-output capacitance: Reduces output signal transients, Frequency response, switch on = 40MHz (typ.), Maximum control input current of 1 µA at 18 V over full package temperature range.
  • Switch on-state resistance matched to within 10 ohm typ. over 15-V signal-input range, High on/off output-voltage ratio: 65 dB typ. @ fis = 10 kHz, RL = 10 k ohm, Low crosstalk between switches: –50 dB typ. @ fis= 0.9 MHz, RL = 1 k ohm, 5-V, 10-V, and 15-V parametric ratings.
  • Example Applications: Analog signal switching/multiplexing: Signal gating, Squelch control, Chopper, Modulator, Demodulator, Commutating switch, Digital signal switching/multiplexing, CMOS logic implementation, Analog-to-digital & digital-to-analog....
Check Stock

Juried Engineering CD4016BE CD4016 4016 100-pA 20-V 1 1 SPST 4-Channel Analog Switch Breadboard-Friendly IC DIP-14 Pack of 5

  • 20-V digital or ± 10-V peak-to-peak switching.
  • 280 ohm- typical on-state resistance for 15-V operation, Matched control-input to signal-output capacitance: Reduces output signal transients, Frequency response, switch on = 40MHz (typ.), Maximum control input current of 1 µA at 18 V over full package temperature range.
  • Switch on-state resistance matched to within 10 ohm typ. over 15-V signal-input range, High on/off output-voltage ratio: 65 dB typ. @ fis = 10 kHz, RL = 10 k ohm, Low crosstalk between switches: –50 dB typ. @ fis= 0.9 MHz, RL = 1 k ohm, 5-V, 10-V, and 15-V parametric ratings.
  • Example Applications: Analog signal switching/multiplexing: Signal gating, Squelch control, Chopper, Modulator, Demodulator, Commutating switch, Digital signal switching/multiplexing, CMOS logic implementation, Analog-to-digital & digital-to-analog....
Check Stock

PWM Signal Converter Module Digital to Analog Voltage Converter Adapter White

  • PWM voltage converter Convert 0-100% PWM digital signal into analog signal..
  • Signal interface switching between single chip or other industrial control board..
  • The power supply has the function of reverse connect protection, safe to use ..
  • Input digital signal can be 24V level 0-100%PWM signal. Output analog signal can be 0-10V voltage..
  • PWM signal receiving frequency range: 100hz-3khz, recommended 1khz-3khz..
Check Stock

Diamond Audio MICRO4V2 4-Channel 600 Watts RMS Class D Amplifier

  • ...hnology | Bridgeable for high power operation (CH1+CH2/CH3+CH4) | Balanced differential inputs for superior noise rejection.
  • Input sensitivity from 200mV to 10V accepts Line (RCA) and Speaker level input | Input selector switch (2 CH / 4 CH) | Selectable auto-turn-on mode: Signal Sensing (VOX), 12V Remote (REM) and DC offset (DC) | Fully variable, 12dB per octave, electronic crossovers | Built-in BTR Port (MICRO-USB) to connect our optional Bluetooth receiver-controller | Illuminated logo.
  • RMS Power Rating - RMS Power (2Ω): 150W x 4 | RMS Power (4Ω): 80W x 4 | Bridged (mono 1Ω): N/A | Bridged (mono 2Ω): N/A | Bridged (mono 4Ω): 300W x 2 | Topology: Full Range Class D Power Supply | Power Supply: Full PWM | Power Supply Threshold: 10.0VDC - 17.0VDC | Idle Current: (0.7A).
  • Distortion - THD 4 (1KHx @ 4Ω): 0.5% | S/N Ratio (A weighted @1W): -85dBA | S/N Ratio (A weighted @FP): -101.1dBA | Input Sensitivity - Low Input Level: 200mV - 10.0V | High Input Level: N/A | Input Impedance - Low Input Level: 20KΩ | High Input Level: 20KΩ.
  • Output Stage - Output Impedance: 0.018Ω | Dampin....
Check Stock